A multimeter is a flexible instrument that can be utilized to check quite a lot of electrical parts, together with capacitors. Capacitors are used to retailer electrical power and are present in a variety of digital units. Testing a capacitor with a multimeter is a comparatively easy course of, however it is very important comply with the proper steps to make sure correct outcomes. Earlier than beginning, discharge the capacitor to keep away from {an electrical} shock
The diode setting can be utilized to examine for a brief circuit in a capacitor. Join the optimistic probe of the multimeter to the optimistic terminal of the capacitor and the unfavorable probe to the unfavorable terminal. A brief circuit will likely be indicated by a studying of zero ohms.
Capacitance mode on the multimeter offers capacitance readings if the capacitor is sweet. If the capacitor is unhealthy, the multimeter will show “OL” which means “open loop” and point out no connection or an infinite worth.
Setting the Multimeter to Capacitance Mode
To precisely take a look at a capacitor utilizing a multimeter, it’s important to set the machine to the suitable mode for measuring capacitance. Completely different multimeters could have barely totally different procedures for setting the capacitance mode, however here is a common information:
-
Choose the Capacitance Vary: Most multimeters have a rotary dial or a push-button to pick out the measurement vary. Search for the vary that’s acceptable for the capacitor you might be testing. For instance, in case you are testing a capacitor with a capacitance of 10 μF, choose the vary of 100 μF or increased.
-
Set the Multimeter to Capacitance Mode: Multimeters usually have a operate selector change or a push-button to decide on the measurement mode. Find the setting labeled “Capacitance” (often denoted by the image “F” or “C”).
-
Join the Take a look at Leads: Join the black take a look at result in the COM (widespread) terminal on the multimeter and the pink take a look at result in the terminal designated for capacitance measurement.
Extra Suggestions for Setting Capacitance Mode
-
If the multimeter has an autoranging function, it’s going to routinely choose the suitable capacitance vary and mode.
-
Seek the advice of the multimeter’s consumer guide for particular directions on setting the capacitance mode.
-
Earlier than testing a capacitor, it’s good observe to discharge it by shorting its terminals with an insulated instrument.
Capacitance Ranges for Completely different Kinds of Capacitors
The suitable capacitance vary to pick out is determined by the kind of capacitor being examined. Here is a desk in your reference:
| Capacitor Sort | Typical Capacitance Vary |
|---|---|
| Ceramic | 1 pF – 1 μF |
| Electrolytic | 1 μF – 10,000 μF |
| Movie | 1 nF – 100 μF |
| Tantalum | 1 μF – 100 μF |
Figuring out Capacitance Worth
To find out the capacitance worth of a capacitor, comply with these steps:
- Set the multimeter to the capacitance measurement mode.
- Join the optimistic take a look at result in the optimistic terminal of the capacitor and the unfavorable take a look at result in the unfavorable terminal.
- Learn the capacitance worth displayed on the multimeter.
- If the capacitance worth could be very small or very giant, the multimeter could not have the ability to measure it precisely. On this case, you should use an exterior capacitor tester.
- The capacitance worth of a capacitor is measured in farads (F). Nonetheless, capacitors typically have very small capacitance values, so they’re usually measured in microfarads (µF), nanofarads (nF), or picofarads (pF).
Capacitance Desk
| Capacitance Vary | Items |
|---|---|
| 1 – 999.99 µF | µF |
| 0.001 – 999.9 nF | nF |
| 0.001 – 999.9 pF | pF |
Discharging Capacitors Safely
Earlier than testing a capacitor with a multimeter, it’s essential to discharge it correctly to stop electrical shock. Listed below are the steps to discharge a capacitor safely:
1. Establish the Capacitor
Find the capacitor you want to discharge. It should often have a cylindrical or rectangular form with two terminals.
2. Collect Vital Supplies
You will have an insulated screwdriver, a pair of insulated pliers, and a discharge resistor (if obtainable).
3. Quick the Terminals
With the screwdriver or pliers, briefly contact the 2 terminals of the capacitor collectively. This may discharge the capacitor by means of the resistance of the instruments.
4. Verify for Discharge
Utilizing a multimeter set to the voltage vary of the capacitor, join the probes to the terminals. If the voltage studying is close to zero, the capacitor is discharged.
5. Use a Discharge Resistor (Elective)
If a discharge resistor is offered, join it throughout the capacitor terminals for a couple of minutes earlier than shorting them. This supplies a extra managed discharge path.
6. Floor the Capacitor
Join a wire from one of many capacitor terminals to a grounded metallic floor, reminiscent of a water pipe or {an electrical} outlet cowl plate.
7. Discharge Via a Resistor
Join a resistor of acceptable wattage and resistance (usually 100 ohms or increased) throughout the capacitor terminals. Go away it linked for some time to make sure full discharge.
8. Double Verify and Insulate
After discharging, wait a couple of minutes and re-check the voltage utilizing a multimeter. Cowl the terminals with insulating tape or caps to stop unintended contact.
| Capacitor Sort | Discharge Methodology |
|---|---|
| Electrolytic | Quick terminals and wait (no resistor required) |
| Ceramic, Movie, Tantalum | Quick terminals utilizing screwdriver or pliers |
| Excessive-Voltage | Use discharge resistor and floor |
Capacitor Discharge
Earlier than testing a capacitor, it is essential to discharge it. All the time put on correct security gear and use a discharge instrument or a resistor to empty the saved power. Failure to discharge the capacitor may end up in electrical shock or injury to the multimeter.
Capacitance Measurement
Set the multimeter to the capacitance measurement vary, usually denoted by the “F” image. Join the optimistic result in the optimistic terminal of the capacitor and the unfavorable result in the unfavorable terminal. The multimeter will show the capacitance worth in farads (F).
ESR Measurement
Some multimeters can measure the equal collection resistance (ESR) of a capacitor. ESR is a vital parameter that impacts the capacitor’s efficiency and lifespan. Set the multimeter to the ESR measurement vary, join the probes to the capacitor terminals, and skim the displayed ESR worth.
Leakage Present Take a look at
Join the capacitor in collection with a high-value resistor (e.g., 1 MΩ) and a voltage supply. Measure the voltage throughout the resistor utilizing a multimeter set to the millivolt vary. The leakage present might be calculated utilizing Ohm’s legislation: I = V/R.
Polarity Verify
For electrolytic capacitors, it is important to examine the polarity earlier than testing. Join the optimistic lead of the multimeter to the optimistic terminal of the capacitor and the unfavorable result in the unfavorable terminal. If the polarity is inaccurate, the multimeter will show a unfavorable capacitance worth.
Troubleshooting Capacitor Points
Open Capacitor
An open capacitor may have infinite resistance and nil capacitance. The multimeter will show “OL” or a really excessive resistance worth.
Shorted Capacitor
A shorted capacitor may have very low resistance and excessive capacitance. The multimeter will show a really low resistance worth or “0L”.
Capacitance Drift
Capacitance drift signifies a change within the capacitor’s capacitance worth over time. The multimeter can be utilized to observe capacitance adjustments beneath totally different circumstances (e.g., temperature, voltage).
Leakage Present Exceeds Specs
Extreme leakage present can result in capacitor failure. The multimeter can be utilized to measure leakage present and examine it to the producer’s specs.
Polarity Reversed
For electrolytic capacitors, reversing the polarity can injury the capacitor. The multimeter can be utilized to examine the polarity and guarantee it’s appropriate.
Deciphering Multimeter Readings
10. Measurement Scales
Multimeters supply varied measurement scales for capacitors, usually starting from nanofarads (nF) to microfarads (µF). Select the suitable scale primarily based on the capacitor’s anticipated capacitance. For instance, if testing a capacitor with a capacitance of 100 µF, choose the µF scale for correct readings.
| Capacitance Vary | Measurement Scale |
|---|---|
| 0.1 pF – 1 nF | pF |
| 1 nF – 1 µF | nF |
| 1 µF – 100 µF | µF |
Easy methods to Use a Multimeter to Take a look at a Capacitor
1. Set your multimeter to the capacitance vary.
2. Join the optimistic lead of the multimeter to 1 lead of the capacitor and the unfavorable result in the opposite lead.
3. The multimeter will show the capacitance of the capacitor in farads (F).
4. If the capacitor is working correctly, the capacitance studying ought to be inside the tolerance vary specified by the producer.
Individuals Additionally Ask
How do I do know if my capacitor is unhealthy?
There are a number of methods to inform if a capacitor is unhealthy. A technique is to make use of a multimeter to check the capacitance. If the capacitance studying is considerably decrease than the desired worth, the capacitor could also be unhealthy.
What’s the tolerance vary for a capacitor?
The tolerance vary for a capacitor is the vary of values that the capacitance can range from the desired worth. The tolerance vary is often expressed as a share of the desired worth.
