Changing the battery on a Dell Perc 710 is a comparatively easy process that may be accomplished in a couple of minutes. Nevertheless, you will need to take precautions to keep away from damaging the controller or the battery. To finish, this process, it’s possible you’ll want a Phillips #0 screwdriver, a brand new battery, and an anti-static wrist strap. An anti-static wrist strap just isn’t required however it’s endorsed to keep away from damaging the controller resulting from electrostatic discharge.
Earlier than you start, energy down the server and unplug it from the facility outlet. As soon as the server is powered down, take away the entrance bezel of the server. Find the Perc 710 controller and take away the 2 screws that safe it to the chassis. As soon as the screws are eliminated, fastidiously slide the controller out of the chassis. Find the battery on the controller and press down on the discharge tab. The battery will pop up and could be eliminated. Take the brand new battery and insert it into the controller. Press down on the battery till it clicks into place. Slide the controller again into the chassis and safe it with the 2 screws. Reinstall the entrance bezel of the server and plug it again into the facility outlet.
As soon as the server is powered on, the brand new battery will start charging. The battery usually takes about 24 hours to totally cost. As soon as the battery is absolutely charged, it would present energy to the controller within the occasion of an influence failure. It is very important exchange the battery each three to 5 years to make sure that the controller has a dependable energy supply.
Security Precautions
When changing the PERC 710 battery, you will need to take the next security precautions to keep away from potential hazards and guarantee a clean and profitable course of:
1. Energy Off and Unplug the System:
1.1 Energy Off the System: Earlier than trying any {hardware} upkeep, at all times energy off the system correctly to stop information loss and {hardware} harm. To do that, comply with these steps:
- Click on on the “Begin” menu and choose “Shut Down”.
- Await the system to close down fully earlier than continuing.
1.2 Unplug the Energy Twine: As soon as the system is powered off, unplug the facility wire from {the electrical} outlet to make sure that the system is totally de-energized.
2. Precautions to Keep away from Electrostatic Discharge (ESD):
ESD can harm delicate digital elements. To keep away from this, take the next precautions:
- Floor your self by touching a steel floor or sporting an anti-static wrist strap earlier than dealing with the PERC 710 battery.
- Solely deal with the battery by its edges or connector to keep away from touching the uncovered digital elements.
- Work on an anti-static mat or in an ESD-protected space.
- Place the previous battery in an anti-static bag earlier than disposal.
3. Consult with the System Guide:
For particular directions and security precautions associated to your explicit Dell server mannequin, consult with the system’s person handbook or technical documentation.
Gathering Essential Instruments
To efficiently exchange the Dell Perc 710 battery, you’ll require a number of important instruments to make sure a secure and environment friendly course of.
The next desk summarizes the mandatory instruments:
| Device |
|---|
| Anti-static wrist strap |
| Phillips #1 screwdriver |
| Tweezers (non-obligatory) |
Anti-static Wrist Strap:
An anti-static wrist strap is essential to stop electrostatic discharge (ESD), which might harm delicate digital elements just like the Perc 710 battery. Put on the strap by attaching its steel snap to a grounded floor and the elastic band to your wrist.
Phillips #1 Screwdriver:
A Phillips #1 screwdriver is crucial for eradicating and tightening the screws that safe the battery housing. Guarantee you may have a driver with a safe match and a pointy tip to keep away from damaging the screw heads.
Tweezers (Non-obligatory):
Tweezers could be useful for manipulating small elements, such because the battery connector, if vital. Nevertheless, if you’re uncomfortable utilizing tweezers, you should use your fingertips with warning.
Finding and Eradicating the Battery
The Perc 710 battery is positioned on the entrance of the cardboard, subsequent to the backplane connectors. To take away the battery, comply with these steps:
- Energy down the system and unplug it from the facility outlet.
- Find the Perc 710 card within the system.
- Unplug the battery from the Perc 710 card. The battery is a small, black cylinder with a white connector.
Changing the Battery
After you have eliminated the previous battery, you’ll be able to set up the brand new one. To do that, comply with these steps:
- Align the brand new battery with the connector on the Perc 710 card.
- Press down on the battery till it clicks into place.
- Plug the system again into the facility outlet and energy it on.
Verifying the Battery Set up
After you have changed the battery, you must confirm that it’s put in accurately. To do that, comply with these steps:
- Log into the Perc 710 net interface.
- Click on on the “Configuration” tab.
- Click on on the “Battery” sub-tab.
The Battery Standing web page will show the standing of the battery. The battery needs to be listed as “OK” and the cost stage needs to be above 50%.
| Battery Standing | Description |
|---|---|
| OK | The battery is put in accurately and is functioning correctly. |
| Warning | The battery is low on energy and must be changed. |
| Crucial | The battery is critically low on energy and the system is not going to boot if the battery just isn’t changed. |
Inserting the New Battery
4. Insert the brand new battery:
-
Find the battery connector on the Perc 710 card. It is a small, black connector positioned close to the entrance of the cardboard.
-
Take away the previous battery by fastidiously lifting it straight up from the connector. Don’t pry or drive it.
-
Align the brand new battery with the connector and insert it fastidiously. Be certain that to push it down firmly till it clicks into place.
-
Confirm that the battery is securely seated by gently wiggling it back and forth. If it strikes, repeat steps 3 and 4.
-
As soon as the battery is correctly put in, the Perc 710 card ought to routinely detect and acknowledge it. If it does not, energy cycle the server to drive a refresh.
Word: The next desk summarizes the steps for inserting the brand new battery:
| Step | Motion |
|---|---|
| 1 | Find the battery connector on the Perc 710 card. |
| 2 | Take away the previous battery by fastidiously lifting it straight up from the connector. |
| 3 | Align the brand new battery with the connector and insert it fastidiously. Push it down firmly till it clicks into place. |
| 4 | Confirm that the battery is securely seated by gently wiggling it back and forth. If it strikes, repeat steps 3 and 4. |
| 5 | Energy cycle the server to drive a refresh if the Perc 710 card does not routinely detect the brand new battery. |
Connecting the Energy Cable
Observe these steps to attach the facility cable:
- Make sure that the PERC 710 backplane is securely put in within the chassis.
- Find the facility cable that got here together with your PERC 710.
- Join one finish of the facility cable to the facility connector on the PERC 710 backplane.
- Join the opposite finish of the facility cable to an influence outlet.
- Detailed Steps for Connecting the Energy Cable:
Step Description 1 Establish the facility connector on the PERC 710 backplane. It’s positioned on the bottom-left nook of the backplane, subsequent to the battery. 2 Align the arrow on the facility cable with the corresponding arrow on the facility connector. 3 Firmly insert the facility cable into the connector till it clicks into place. 4 Safe the facility cable by tightening the retaining screw. - Confirm that the facility LED on the PERC 710 backplane is lit, indicating that energy is being equipped to the controller.
Verifying the Alternative
As soon as the brand new battery is put in, it is essential to confirm if it is functioning accurately. Observe these detailed steps:
-
Restart the server: Flip off the server, wait a number of seconds, after which energy it again on. This step will enable the server to acknowledge the brand new battery.
-
Log in to the system: Entry the server’s working system and log in as an administrator.
-
Test the BIOS settings: Enter the server’s BIOS settings and navigate to the “System Configuration” or “RAID Configuration” menu. Find the “Battery Standing” part and confirm if the battery is detected and its standing is “Optimum” or “OK.”
-
Run a diagnostic take a look at: Most Dell servers have built-in diagnostic instruments that may take a look at the battery’s well being. Consult with the server’s documentation for particular directions on operating the diagnostic take a look at.
-
Monitor the occasion log: The server’s occasion log could comprise details about the battery’s standing. Test the log for any errors or warnings associated to the battery.
-
Observe the bodily indicator: Some Dell servers have a bodily indicator, reminiscent of an LED gentle, that reveals the battery’s standing. Make sure that the indicator is inexperienced or one other colour indicating a wholesome battery.
If any of those steps point out an issue with the brand new battery, contact Dell Technical Help for additional help.
| Step | Motion |
|---|---|
| 1 | Restart the server |
| 2 | Log in to the system |
| 3 | Test the BIOS settings |
| 4 | Run a diagnostic take a look at |
| 5 | Monitor the occasion log |
| 6 | Observe the bodily indicator |
Changing the Cowl
As soon as the battery has been changed, you will need to exchange the duvet to guard the inner elements of the PERC 710 card. To exchange the duvet, comply with these steps:
1. Connect the Battery Cowl
Align the battery cowl with the PERC 710 card and slide it into place till it clicks securely.
2. Safe the Battery Cowl (Non-obligatory)
Relying on the chassis, an non-obligatory screw can be utilized to safe the battery cowl in place. If out there, find the screw gap on the battery cowl and tighten the screw to safe the duvet.
Superior Troubleshooting: Addressing Battery Cowl Errors
In some circumstances, after changing the battery, the PERC 710 card could show an error message indicating an issue with the battery cowl. To resolve this situation, comply with these steps:
-
Test the Battery Cowl Connection: Make sure that the battery cowl is absolutely seated and securely connected to the PERC 710 card.
-
Clear the Battery Cowl Contacts: Examine the battery cowl contacts for any particles or corrosion. Gently clear the contacts with a delicate fabric to take away any contaminants.
-
Reset the PERC 710 Card: If cleansing the contacts doesn’t resolve the difficulty, strive resetting the PERC 710 card. To do that, energy down the server, take away the PERC 710 card, after which reinsert it.
| Symptom | Trigger | Resolution |
|---|---|---|
| Battery Learn Error | Defective battery cowl connection | Test and safe the connection |
| Battery Cowl Not Detected | Soiled battery cowl contacts | Clear the contacts |
| Battery Cowl Tamper Error | Cowl has been opened | Reset the PERC 710 card |
Configuring the BIOS
To begin the method of changing the battery in your Dell Perc 710, you will want to configure the BIOS settings. Listed here are the steps to do that:
1. Energy on the server and press F2 to enter the BIOS Setup Utility.
2. Navigate to the “System Configuration” menu.
3. Choose “iDRAC Settings” and press Enter.
4. Choose “PERC Settings” and press Enter.
5. Choose “Battery Configuration” and press Enter.
6. Choose “Exchange Battery” and press Enter.
7. The system will now immediate you to substantiate that you just need to exchange the battery. Press “Y” to substantiate.
8. The system will now exchange the battery. This course of could take a number of minutes. As soon as the method is full, the system will show a message indicating that the battery has been changed efficiently. Press any key to proceed.
Here’s a desk summarizing the steps for configuring the BIOS:
| Step | Motion |
|---|---|
| 1 | Energy on the server and press F2 to enter the BIOS Setup Utility. |
| 2 | Navigate to the “System Configuration” menu. |
| 3 | Choose “iDRAC Settings” and press Enter. |
| 4 | Choose “PERC Settings” and press Enter. |
| 5 | Choose “Battery Configuration” and press Enter. |
| 6 | Choose “Exchange Battery” and press Enter. |
| 7 | Affirm that you just need to exchange the battery. |
| 8 | The system will exchange the battery. |
How To Exchange Dell Perc 710 Battery
The PERC H710, PERC H810, and H710P mini cache battery is a small part that powers the cache on the RAID controller. If the battery fails, the cached information might be misplaced, which might result in information corruption or loss. It is very important exchange the battery often to stop this from occurring.
Troubleshooting Battery Points
If you’re having issues together with your PERC H710, PERC H810, or H710P mini cache battery, there are some things you are able to do to troubleshoot the difficulty.
1. Test the LED
The PERC H710, PERC H810, and H710P mini cache battery has an LED that signifies the standing of the battery. If the LED is off, the battery just isn’t receiving energy. If the LED is blinking, the battery is nearing the top of its life and must be changed.
2. Test the occasion log
The PERC H710, PERC H810, and H710P mini cache battery will log occasions to the system occasion log. If the battery is failing, there might be an occasion logged within the occasion log.
3. Exchange the battery
You probably have decided that the battery is failing, you will want to exchange it. The battery is a small, coin-shaped battery that’s positioned on the RAID controller. To exchange the battery, comply with these steps:
1. Energy down the server.
2. Take away the duvet from the server.
3. Find the RAID controller.
4. Take away the battery from the RAID controller.
5. Insert the brand new battery into the RAID controller.
6. Exchange the duvet on the server.
7. Energy on the server.
4. Replace the firmware
If you’re nonetheless having issues with the PERC H710, PERC H810, or H710P mini cache battery, it’s possible you’ll have to replace the firmware. The firmware is the software program that controls the operation of the RAID controller. Updating the firmware can repair bugs and enhance the efficiency of the RAID controller.
5. Contact Dell help
If you’re unable to resolve the difficulty your self, you’ll be able to contact Dell help for help. Dell help may also help you troubleshoot the difficulty and offer you a alternative battery if vital.
6. Battery Life
The PERC H710, PERC H810, and H710P mini cache battery has a lifespan of about 3 years. After 3 years, the battery will have to be changed.
7. Battery Alternative Price
The price of a PERC H710, PERC H810, or H710P mini cache battery is about $100.
8. Battery Alternative Interval
The PERC H710, PERC H810, and H710P mini cache battery needs to be changed each 3 years.
9. Battery Capability
| Battery Mannequin | Capability (mAh) |
|---|---|
| CR2032 | 225 |
| CR2025 | 160 |
| CR2016 | 90 |
Instruments Required
• Phillips #2 screwdriver
• Anti-static wrist strap
Step-by-Step Directions
1. Security Precautions
• Disconnect the server from all energy sources.
• Floor your self by sporting an anti-static wrist strap.
2. Take away the Entrance Bezel
• Unclip the bezel from the highest and gently pull it ahead.
3. Take away the Battery Module
• Find the battery module on the prime of the RAID controller card.
• Grasp the battery module firmly and pull it straight up.
4. Insert the New Battery
• Align the brand new battery with the slot on the controller card.
• Push the battery down into place.
5. Reinstall the Entrance Bezel
• Slide the entrance bezel again into place till it clicks.
6. Energy on the Server
• Reconnect the facility cables and restart the server.
Suggestions for Sustaining Battery Well being
• Hold the server in a cool, dry setting.
• Keep away from exposing the battery to excessive temperatures.
• Don’t try and recharge the battery.
• Exchange the battery each 3-5 years or when the battery indicator gentle turns purple.
• If the battery fails, the RAID controller will lose its configuration information. Guarantee that you’ve common backups of your information to stop potential information loss.
• Use a UPS (Uninterruptible Energy Provide) to guard the server from energy outages. This may stop the battery from draining and inflicting information loss.
• Monitor the battery standing often. The battery standing could be checked utilizing the Dell OpenManage Server Administrator (OMSA) utility.
• If the battery standing reveals indicators of degradation, exchange the battery as quickly as attainable to keep away from information loss.
How you can Exchange Dell Perc 710 Battery
The Dell Perc 710 battery is a small, replaceable battery that gives energy to the RAID controller. The battery is positioned on the entrance of the RAID controller and is simple to exchange. Listed here are the steps on easy methods to exchange the Dell Perc 710 battery:
- Energy down the server and unplug it from the facility outlet.
- Open the server case and find the RAID controller.
- Press the discharge latch on the entrance of the RAID controller and slide the controller out of the chassis.
- Find the battery on the entrance of the RAID controller. The battery is a small, cylindrical battery with a black plastic cowl.
- Press the discharge tab on the battery and slide the battery out of the controller.
- Insert the brand new battery into the controller and slide it into place.
- Slide the RAID controller again into the chassis and shut the server case.
- Plug the server again into the facility outlet and energy it on.
Individuals Additionally Ask About How you can Exchange Dell Perc 710 Battery
How usually ought to I exchange the Dell Perc 710 battery?
The Dell Perc 710 battery needs to be changed each three to 5 years.
What occurs if the Dell Perc 710 battery fails?
If the Dell Perc 710 battery fails, the RAID controller will lose energy and the information on the RAID array might be vulnerable to being misplaced.
Can I exchange the Dell Perc 710 battery myself?
Sure, you’ll be able to exchange the Dell Perc 710 battery your self. The process is straightforward and solely requires a number of fundamental instruments.
