Changing a two-handle bathtub faucet shouldn’t be as troublesome as it could appear. With just a few easy instruments and somewhat little bit of persistence, you possibly can have your new faucet put in very quickly.
Step one is to show off the water provide to the tub. That is normally finished by turning off the valves situated beneath the sink. As soon as the water is turned off, you possibly can take away the previous faucet by unscrewing the nuts that maintain it in place. Watch out to not harm the plumbing if you find yourself doing this.
As soon as the previous faucet is eliminated, you possibly can set up the brand new one. Begin by inserting the brand new faucet within the gap within the bathtub. Then, screw on the nuts that maintain it in place. Make sure to tighten the nuts securely, however don’t overtighten them. Lastly, activate the water provide and examine for leaks. If there are any leaks, tighten the nuts till the leaks cease.
Collect Vital Instruments and Supplies
Changing a two-handle bathtub faucet requires just a few important instruments and supplies to make sure a easy and profitable set up. This is a complete record of what you will want:
Instruments
- Adjustable wrench or spanner
- Phillips head screwdriver
- Flat head screwdriver
- Plumbers putty or Teflon tape
- Bucket or bowl
- Rags or towels
Supplies
| Element | Amount |
|---|---|
| New two-handle bathtub faucet | 1 |
| Faucet handles | 2 |
| Faucet aerators (non-obligatory) | 2 |
| Pipe dope or thread sealant | As wanted |
Moreover, it’s possible you’ll need to take into account bringing a flashlight for higher visibility beneath the sink and a pair of labor gloves for cover.
Flip Off Water
Earlier than you start engaged on the tap, it is necessary to show off the water provide. This can stop water from spraying out of the tap whenever you take away the handles and cartridge. To show off the water provide, find the shut-off valves beneath the sink. The valves will sometimes be situated on the base of the tap, the place the water strains connect with the tap. Flip the valves clockwise to show off the water provide.
If there are not any shut-off valves beneath the sink, you have to to show off the water provide to your entire home. To do that, find the principle water shut-off valve, which is normally situated close to the entrance of the home, within the basement, or in a utility closet. Flip the valve clockwise to show off the water provide.
Ideas for Turning Off the Water
Listed here are just a few ideas for turning off the water provide:
- Just remember to have a wrench or pliers available to show the shut-off valves.
- If the shut-off valves are troublesome to show, you possibly can attempt utilizing a pair of pliers to get a greater grip.
- In case you are unable to show off the water provide, it’s best to name a plumber for help.
| Device | Goal |
| Wrench or pliers | To show the shut-off valves |
Take away Aerators and Handles
Eradicating Aerators
Begin by unscrewing the aerator from the tap utilizing a wrench. If the aerator is caught, you should utilize a pair of pliers to softly loosen it.
As soon as the aerator is eliminated, it is possible for you to to see the cartridge. The cartridge is held in place by a screw, which you have to to take away utilizing a screwdriver.
As soon as the screw is eliminated, it is possible for you to to carry the cartridge out of the tap. Watch out to not lose the washer that’s situated behind the cartridge.
Eradicating Handles
To take away the handles, you have to to find the set screws which can be holding them in place. The set screws are normally situated on the underside of the handles.
After you have situated the set screws, you have to to loosen them utilizing a screwdriver. Watch out to not over-tighten the set screws, as this could harm the handles.
As soon as the set screws are loosened, it is possible for you to to drag the handles off the tap.
| Device | Description |
|---|---|
| Wrench | Used to unscrew the aerator. |
| Screwdriver | Used to take away the cartridge screw and set screws. |
| Pliers | Used to loosen a caught aerator. |
| Washer | Positioned behind the cartridge, it should not be misplaced. |
| Set screws | Maintain the handles in place. |
Disconnect Provide Traces
As soon as the handles and trim are eliminated, you have to to disconnect the availability strains. These are the versatile hoses that join the tap to the water provide pipes. Use an adjustable wrench to loosen the nuts that join the hoses to the tap.
Watch out to not overtighten the nuts, as you possibly can harm the hoses. As soon as the nuts are free, you possibly can fastidiously pull the hoses off the tap.
If the hoses are previous or broken, it’s possible you’ll want to switch them. To do that, reduce the previous hoses off the tap and the availability pipes. Then, connect the brand new hoses to the tap and the availability pipes utilizing the nuts that got here with the brand new hoses.
As soon as the availability strains are disconnected, you possibly can take away the previous faucet from the sink or tub.
| Ideas |
|---|
| In case you are having hassle disconnecting the availability strains, you should utilize a pair of pliers that will help you loosen the nuts. |
| Watch out to not harm the availability strains if you find yourself disconnecting them. |
| In case you are changing the availability strains, be sure that they’re the right size and that they’re rated for the water strain in your house. |
Take away Faucet Base
After eradicating the handles and cartridge, now you can take away the tap base. Place a bucket or towel beneath the tap to catch any water that will leak out.
Utilizing an adjustable wrench, loosen the nuts which can be holding the tap base in place. Watch out to not overtighten the nuts, as this could harm the tap.
As soon as the nuts are free, you possibly can gently pull the tap base off of the bathtub deck.
If the tap base is caught, it’s possible you’ll want to make use of a rubber mallet to softly faucet it free. Watch out to not hit the tap too laborious, as this could harm it.
As soon as the tap base is eliminated, now you can entry the plumbing connections.
Ideas for Eradicating the Faucet Base
| Ideas | Particulars |
|---|---|
| Use a bucket or towel to catch any water that will leak out | This can assist to forestall water from damaging your ground or carpet. |
| Watch out to not overtighten the nuts | Overtightening the nuts can harm the tap. |
| If the tap base is caught, use a rubber mallet to softly faucet it free | Watch out to not hit the tap too laborious, as this could harm it. |
Clear Mounting Floor
Earlier than you start putting in the brand new faucet, it is necessary to totally clear the mounting floor. This can assist to make sure that the brand new faucet is put in securely and that there are not any leaks. Listed here are the steps to scrub the mounting floor:
-
Take away any previous caulk or sealant from across the previous faucet. You need to use a utility knife or a razor blade to fastidiously scrape away the caulk.
-
Clear the floor with a degreaser. This can assist to take away any filth, grime, or oil that might stop the brand new faucet from bonding correctly.
-
Rinse the floor with clear water and permit it to dry utterly.
| Tip | Description |
|---|---|
| Use a scrub brush to scrub the floor totally. | This can assist to take away any cussed filth or grime. |
| Enable the floor to dry utterly earlier than putting in the brand new faucet. | This can assist to make sure that the brand new faucet is put in securely. |
Apply Plumber’s Putty and Set up Base
Step 7: Apply Plumber’s Putty and Set up Base
7.1: Take away the previous plumber’s putty from the bottom of the brand new faucet utilizing a putty knife or scraper. Clear the world totally with rubbing alcohol and permit it to dry.
7.2: Roll out a rope of plumber’s putty about 1/4 inch thick and 6 inches lengthy. Place the putty across the base of the tap, leaving a small gap within the heart for the water provide strains.
7.3: Flip the tap the other way up and place it over the mounting holes within the bathtub. Ensure that the putty is evenly distributed across the base and filling any gaps.
7.4: Place the mounting bolts via the holes within the faucet and into the tub. Tighten the nuts by hand till comfortable.
7.5: Flip the tap right-side up and manually tighten the mounting nuts additional. Keep away from overtightening, as this could harm the tap or bathtub.
7.6: Use a degree to make sure the tap is degree. Alter the mounting nuts as obligatory.
Set up Handles
1. Place the handles on the stems.
2. Apply a small quantity of plumbers grease to the threads of the deal with screws.
3. Insert the deal with screws into the handles and tighten them till they’re comfortable.
4. Use a wrench to tighten the packing nuts on every deal with.
5. Activate the water and examine for leaks. If there’s a leak, tighten the packing nuts till the leak stops.
6. Set up the aerators on every deal with.
7. Activate the water and examine for leaks. If there’s a leak, tighten the aerators till the leak stops.
8. Test the operation of the tap. The handles ought to flip easily and the water ought to stream evenly from the aerators. If the tap doesn’t function correctly, examine the next:
| Attainable Drawback | Resolution |
|---|---|
| The handles are stiff | Loosen the packing nuts on the handles |
| The water doesn’t stream evenly from the aerators | Clear the aerators |
| The tap is leaking | Tighten the packing nuts on the handles or aerators |
Join Provide Traces
9. **Join Provide Traces to Faucet:**
a. Wrap plumber’s tape clockwise across the threaded finish of the cold and warm provide strains. Tighten them by hand onto the corresponding faucet inlets marked “H” and “C.”
b. **Use a Basin Wrench to Safe:**
| Tip | Profit |
|---|---|
| Insert a basin wrench into the opening within the faucet physique. | Permits entry to the nuts beneath the tap. |
| Tighten the nuts till they’re comfortable, however keep away from overtightening. | Prevents leaks and ensures a safe connection. |
c. **Test Connections:**
Activate the water provide and examine for leaks on the faucet inlets and provide line connections. If any leaks happen, tighten the connections additional as wanted.
Flip On Water and Test for Leaks
As soon as the previous faucet is eliminated, it is essential to activate the water provide to check for any potential leaks earlier than putting in the brand new one. Observe these steps to make sure a watertight seal:
- Open each the cold and warm water valves situated beneath the sink.
- Run each handles to permit water to stream via the pipes.
- Examine the bottom of the tap, the availability strains, and another connections for any indicators of water leakage.
- For those who encounter any leaks, tighten the connections additional utilizing a wrench or pliers.
- As soon as the leaks have been addressed, flip off each water valves once more.
- Proceed with the set up of the brand new faucet, taking additional care to safe all connections.
- As soon as the brand new faucet is totally put in, activate the water valves once more and examine for any remaining leaks.
- If all connections are safe and there are not any leaks, proceed to the subsequent step of testing the performance of the tap.
- For those who encounter any persistent leaks that can’t be resolved, seek the advice of a licensed plumber for skilled help.
| Troubleshooting Leaks | |
|---|---|
| Leak at faucet base | Tighten the locknut beneath the tap. |
| Leak at provide line connections | Use a wrench to tighten the nuts connecting the availability strains to the tap. |
| Leak at pop-up drain | Test the drain stopper meeting and exchange any worn-out parts. |
How To Exchange A Two Deal with Bathtub Faucet
Changing a two-handle bathtub faucet is a comparatively easy process that may be accomplished in just a few hours. With the fitting instruments and supplies, it can save you your self the price of hiring a plumber.
Instruments and Supplies
• Adjustable wrench
• Basin wrench
• Plumber’s putty
• Teflon tape
• New bathtub faucet
• Utility knife
Directions
- Flip off the water provide to the tub. There must be two shut-off valves situated beneath the sink. Flip the handles clockwise to shut them.
- Open the tub faucet to launch any remaining water strain.
- Use the adjustable wrench to loosen the nuts that maintain the handles in place. Take away the handles.
- Use the basin wrench to loosen the nuts that maintain the tap physique in place. Take away the tap physique.
- Apply a bead of plumber’s putty to the bottom of the brand new faucet physique. Wrap the threads of the tap physique with Teflon tape.
- Set up the brand new faucet physique and tighten the nuts with the basin wrench.
- Set up the handles and tighten the nuts with the adjustable wrench.
- Activate the water provide to the tub and examine for leaks. If there are any leaks, tighten the nuts additional.
Folks Additionally Ask About How To Exchange A Two Deal with Bathtub Faucet
How a lot does it value to switch a tub faucet?
The associated fee to switch a tub faucet can fluctuate relying on the kind of faucet you select and the complexity of the set up. Nonetheless, you possibly can anticipate to pay between $100 and $500 for the tap and set up.
Can I exchange a tub faucet myself?
Sure, you possibly can exchange a tub faucet your self with the fitting instruments and supplies. Nonetheless, if you’re not comfy working with plumbing, it’s best to rent a plumber.
What’s the greatest sort of bath faucet to purchase?
The very best sort of bath faucet for you’ll rely in your wants and preferences. Some widespread kinds of bathtub taps embrace:
- Two-handle taps
- Single-handle taps
- Thermostatic taps
- Sensor taps
