Featured Picture: Image of a toilet being removed from a bathroom floor
Uninterested in your previous, outdated rest room taking over priceless toilet house? Able to improve to a smooth, fashionable mannequin that can make your toilet an oasis of rest? If that’s the case, it is time to learn to take away a bathroom. Do not let the considered plumbing work intimidate you; with the appropriate instruments and a bit of know-how, you’ll be able to deal with this DIY undertaking in a couple of hours. On this complete information, we’ll stroll you thru the complete course of, from gathering the required supplies to detaching the bathroom from the ground, eradicating the previous wax ring, and putting in your new throne. So, seize your toolbox and let’s get began on remodeling your toilet!
Earlier than you start, it is important to collect all the required instruments and supplies. You may want a bathroom wrench, adjustable wrench, utility knife, bucket, sponge, rest room wax ring, new rest room bolts, and a brand new rest room. Moreover, in case your rest room is linked to a bidet, you will additionally want a bidet provide line. Upon getting the whole lot you want, it is time to put together the toilet for the duty forward. Unfold out previous towels or plastic sheeting round the bathroom to guard the ground from water and particles. Shut off the water provide to the bathroom by turning the valve behind it clockwise. Flush the bathroom to empty the tank and bowl. Lastly, disconnect the water provide line from the bathroom’s fill valve.
Now that the preparatory steps are out of the way in which, it is time to detach the bathroom from the ground. Begin by unbolting the bathroom bolts utilizing the bathroom wrench. Maintain the nuts in place with the adjustable wrench whereas loosening the bolts. As soon as the bolts are free, fastidiously elevate the bathroom straight up and off the flange. Be aware to not harm the ground or the bathroom itself. If the bathroom is caught, gently rock it forwards and backwards whereas pulling up. As soon as the bathroom is eliminated, you’ll be able to clear the flange floor with a sponge and utility knife to take away any previous wax ring residue. Lastly, apply a brand new wax ring to the flange and place the brand new rest room on prime, making certain the bolts align with the holes within the flange.
Disconnecting the Water Provide
Earlier than starting any work in your rest room, it’s essential to disconnect the water provide to stop water from flowing into the bowl and inflicting a large number. Observe these steps to securely disconnect the water provide:
Supplies You may Want:
| Merchandise | Description |
|---|---|
| Wrench or adjustable pliers | For turning the shutoff valve |
| Material or towel | For absorbing any water |
Step-by-Step Directions:
1. Find the Shutoff Valve:
Establish the water shutoff valve, which is usually situated beneath the bathroom close to the ground or behind the bathroom tank. The valve will often have a deal with that may be turned by hand. In case you can not find the shutoff valve, examine the principle water provide valve in your residence, which is often discovered within the basement, utility room, or below a sink.
In case your rest room has two provide strains, one for the bathroom tank and one for the bidet (if relevant), you will want to show off each valves.
2. Flip Off the Water Provide:
Use a wrench or adjustable pliers to slowly flip the deal with of the shutoff valve clockwise till it stops. Don’t overtighten the valve. You need to really feel some resistance because the valve closes.
If the valve is troublesome to show, apply a material or towel across the deal with for higher grip. Keep away from utilizing extreme power, as you might harm the valve.
3. Flush the Rest room:
As soon as the water provide is turned off, flush the bathroom to empty the water from the tank and bowl. This may assist forestall any remaining water from inflicting a large number throughout the removing course of.
Flushing and Emptying the Rest room Bowl
Earlier than eradicating the bathroom, it is essential to flush and empty the bathroom bowl to stop any spills or messes throughout the course of. Observe these steps to take action:
Step 1: Flush the Rest room
Press the flush lever down and permit the bathroom to flush fully. This may drain the water from the bowl.
Step 2: Cease the Water Provide
Find the water provide valve, which is often behind the bathroom close to the ground. Flip the valve clockwise to close off the water provide to the bathroom.
Step 3: Drain the Tank
Press the flush lever once more to empty any remaining water from the tank. If the tank does not empty fully, use a moist/dry vacuum to take away the remainder of the water.
Step 4: Use a Plunger
If there’s any water remaining within the bowl, use a plunger to extract it. Place the plunger over the drain gap and pump it a number of occasions to create suction and power the water out.
Step 5: Dry the Rest room Bowl
Use towels or a moist/dry vacuum to dry the bathroom bowl fully. This may forestall any water from spilling out throughout the removing course of.
| Hazard | Precaution |
|---|---|
| Heavy weight | Elevate with a associate or use a dolly. |
| Sharp edges | Put on gloves and security glasses. |
| Water harm | Shut off water provide and drain the bathroom. |
| Hazardous waste | Eliminate previous wax ring and gaskets correctly. |
Lifting the Tank
To securely elevate the bathroom tank, comply with these steps:
- Flip off the water provide: Find the water provide valve behind the bathroom and switch it clockwise to close off the water stream.
- Disconnect the water provide line: Utilizing a wrench, loosen the nut that connects the water provide line to the tank. Enable the remaining water to empty out.
- Take away the tank bolts: The bathroom tank is secured with two bolts that run via the bottom of the tank and into the bottom of the bathroom bowl. Utilizing a wrench, loosen and take away the bolts.
- Elevate the tank: Rigorously elevate the tank straight up and off the bathroom bowl. Keep away from tilting or jolting the tank, as it could break or harm the bathroom base.
Suggestions:
-
If the tank is heavy, ask for help from one other individual.
-
Place a towel or material on the ground beneath the bathroom base to guard it from scratches.
-
If the bolts are rusted or caught, apply penetrating oil to loosen them.
Disconnecting the Fill Valve
Step 1: Flip off the water provide. Find the water shutoff valve behind the bathroom and switch it clockwise to close off the water provide. If there isn’t any shutoff valve, you will want to show off the principle water provide to the home.
Step 2: Flush the bathroom to empty the tank. Maintain down the flush lever till all of the water drains from the tank.
Step 3: Disconnect the water provide line. Use an adjustable wrench to loosen the nut that connects the water provide line to the fill valve. As soon as the nut is free, you’ll be able to pull the water provide line off the fill valve.
Step 4: Take away the fill valve nut. The fill valve nut is situated on the underside of the fill valve. Use a wrench to loosen the nut after which take away it by hand.
Step 5: Take away the fill valve. As soon as the fill valve nut is eliminated, you’ll be able to pull the fill valve straight as much as take away it from the tank. Watch out to not harm the fill valve o-ring when eradicating it.
Fill Valve O-Ring Substitute
The fill valve o-ring is a small rubber gasket that seals the fill valve to the underside of the tank. Over time, the o-ring can change into worn or broken, which might trigger leaks. In case you are experiencing leaks from the underside of the fill valve, you might want to switch the o-ring.
To interchange the fill valve o-ring, merely take away the previous o-ring and exchange it with a brand new one. The brand new o-ring needs to be the identical dimension and form because the previous o-ring.
| Fill Valve O-Ring Sizes |
|---|
| 1/2 inch |
| 3/4 inch |
| 1 inch |
Eradicating the Seat and Lid
To take away the bathroom seat and lid, comply with these steps:
- Find the bolts: The bolts that maintain the seat in place are usually situated behind the bathroom bowl, on both facet of the hinges.
- Loosen the nuts: Utilizing a wrench, flip the nuts that safe the bolts counterclockwise to loosen them.
- Elevate the seat: As soon as the nuts are free, elevate the bathroom seat straight up and off the bowl.
- Take away the lid: If the bathroom lid is separate from the seat, merely elevate it straight as much as take away it.
- Examine the bolts and washers: Test the bolts and washers for any indicators of injury or rust. If they’re broken, they need to get replaced.
- Clear the hinges: Use a moist material to wash the hinges the place the seat was hooked up. This may assist forestall corrosion and make it simpler to reattach the seat later.
Reattaching the Seat and Lid
To reattach the bathroom seat and lid, merely comply with the steps above in reverse order:
- Align the seat and lid with the hinges.
- Place the bolts via the holes within the hinges.
- Tighten the nuts by hand till they’re cosy.
- Use a wrench to tighten the nuts additional, however watch out to not overtighten them.
- As soon as the nuts are tight, double-check that the seat and lid are safe.
Unbolting the Rest room Base
Unbolting the bathroom base is a vital step within the removing course of. This is an in depth information on the way to proceed:
1. **Find the Base Bolts:** They’re often situated on the base of the bathroom, below the flange. Test for 2 bolts about 6 inches aside.
2. **Collect Instruments:** You may want a wrench or adjustable pliers for loosening the bolts.
3. **Disconnect the Water Provide:** Flip off the water valve behind the bathroom and flush the tank to take away any remaining water.
4. **Apply Lubricant:** Spray a penetrating oil or lubricant onto the bolts to loosen any rust or corrosion.
5. **Unscrew the Bolts:** Use the wrench or pliers to loosen the bolts by turning them counterclockwise. In the event that they’re caught, apply extra lubricant and take a look at once more.
6. **Take away the Bolts:** As soon as loosened, fully unscrew the bolts by hand and get rid of them.
7. **Superior Tip for Cussed Bolts:
| State of affairs | Resolution |
|---|---|
| Bolt head rounded off | Use locking pliers or a hack noticed to take away the bolt head. |
| Bolt snapped in half | Drill out the remaining bolt and exchange it with a brand new one. |
| Bolts rusted past restore | Lower the bolts with a hacksaw and use a chisel to pry off the bathroom base. |
Gently Rocking the Rest room
To softly rock the bathroom and loosen it:
| Step | Description |
|---|---|
| 1 | Place your self in entrance of the bathroom, dealing with the tank. |
| 2 | Maintain each side of the bathroom bowl close to the bottom, simply behind the tank bolts. |
| 3 | Grip the bowl firmly and gently rock it forwards and backwards, facet to facet. |
| 4 | Enhance the stress and power barely over a number of rocking motions. |
| 5 | Proceed rocking the bathroom till it begins to maneuver. |
| 6 | As soon as it begins to maneuver, progressively enhance the rocking power to loosen it additional. |
| 7 | If the bathroom stays caught, strive utilizing a penetrating lubricant to the bottom of the bowl. |
| 8 | Apply the lubricant to each side of the bowl, close to the bottom, and let it penetrate for a couple of minutes.
Tip: Use a lubricant particularly designed for lavatory fixtures to keep away from damaging the bathroom. |
| 9 | Resume rocking the bathroom after permitting the lubricant to penetrate. |
| 10 | Repeat steps 3-7 till the bathroom is free sufficient to take away. |
| Step | Description |
|---|---|
| 1 | Take away the nuts from the bolts holding the bathroom to the ground. |
| 2 | Grasp the bathroom bowl on each side and elevate it straight up. |
| 3 | Set the bathroom down on a chunk of cardboard or a towel to guard the ground. |
If there’s any harm, you will want to restore it earlier than you’ll be able to set up a brand new rest room.
Cleansing the Rest room Flange and Flooring
1. Collect obligatory instruments and supplies:
- Rest room bowl cleaner
- Sponge or material
- Bucket
- Plunger
- Gloves
2. Shut off water provide and flush rest room:
- Find the water provide valve behind the bathroom and switch it clockwise to shut.
- Flush the bathroom to empty the bowl.
3. Take away rest room bowl:
- Grip the bathroom bowl firmly and rock it gently to loosen it from the flange.
- Elevate the bathroom straight up and away from the flange.
- Eliminate the bowl correctly.
4. Clear the bathroom flange:
- Scrub the bathroom flange completely with the bathroom bowl cleaner and sponge.
- Take away any particles or mineral buildup.
5. Clear the ground:
- Use a bucket of heat water and a mop or sponge to wash the ground across the flange.
- Scrub any stains or particles completely.
6. Test flange for cracks or leaks:
- Examine the bathroom flange for any cracks or leaks.
- If cracks are discovered, apply a sealant to restore them.
7. Exchange flange if obligatory:
- If the flange is broken past restore, exchange it with a brand new one.
- Observe the producer’s directions for set up.
8. Lubricate the flange:
- Apply a skinny layer of petroleum jelly or wax to the flange to cut back friction and stop leaks.
9. Set up new wax ring:
- Place a brand new wax ring on the flange, aligning it with the bolt holes.
- Press the ring firmly into place.
10. Reinstall rest room bowl:
- Rigorously decrease the bathroom bowl onto the flange, aligning the bolts with the holes.
- Hand-tighten the bolts and use a wrench to safe them additional.
- Don’t overtighten the bolts as this will harm the flange or bowl.
| Tip | Motive |
|---|---|
| Put on gloves when dealing with chemical compounds. | Shield your palms from irritation. |
| Use a moist/dry vacuum to take away giant quantities of water. | Pace up the cleansing course of. |
| Enable the ground to dry fully earlier than reinstalling the bathroom. | Forestall water harm or mould progress. |
How one can Take away a Rest room
Eradicating a bathroom is a comparatively easy plumbing activity that may be accomplished in a couple of hours. By following these steps, you’ll be able to safely and successfully take away your previous rest room and put together for the set up of a brand new one.
Step 1: Collect Your Instruments and Supplies
Earlier than you start, collect the next instruments and supplies:
- Adjustable wrench
- Plumber’s putty knife
- Bucket
- Sponge or rags
- New wax ring (if changing)
Step 2: Flip Off the Water Provide
Find the water provide valve behind the bathroom and switch it off. Flush the bathroom to empty the remaining water from the tank and bowl.
Step 3: Disconnect the Water Provide Line
Use an adjustable wrench to loosen the nuts connecting the water provide line to the fill valve and the bathroom tank. Rigorously take away the road.
Step 4: Take away the Rest room Tank
Find the bolts connecting the bathroom tank to the bowl. Use an adjustable wrench to loosen the bolts, then fastidiously elevate the tank off the bowl and set it apart.
Step 5: Take away the Rest room Bowl
Loosen the nuts connecting the bathroom bowl to the ground flange. Rigorously rock the bathroom bowl forwards and backwards till it loosens, then elevate it straight up and take away it.
Step 6: Clear the Rest room Base
Use a plumber’s putty knife to take away any previous wax ring or sealant from the bathroom base and flooring flange. Clear the surfaces completely to make sure a correct seal for the brand new rest room.
Step 7: Set up the New Rest room
Place a brand new wax ring on the bathroom base. Rigorously elevate the brand new rest room bowl and set it on the ground flange, aligning the bolts with the holes within the base.
Step 8: Reinstall the Rest room Tank
Decrease the bathroom tank onto the bowl and tighten the bolts to safe it. Reconnect the water provide line to the fill valve.
Step 9: Flip On the Water Provide
Activate the water provide valve behind the bathroom. Test for any leaks round the bathroom base or tank.
Folks Additionally Ask
How do I take away a bathroom that’s bolted to the ground?
Observe the steps outlined on this information, together with loosening the bolts connecting the bathroom bowl to the ground flange.
Can I take away a bathroom myself?
Sure, you’ll be able to take away a bathroom your self with the appropriate instruments and supplies. Nonetheless, in case you are not comfy with plumbing duties, it’s all the time advisable to seek the advice of a licensed plumber.
What’s a wax ring and why is it used?
A wax ring is a water resistant sealant that creates a leak-proof seal between the bathroom base and the ground flange. It helps forestall water from leaking out and inflicting harm.
