Changing a heating factor in a Samsung dryer can prevent the price of shopping for a brand new dryer or hiring an equipment restore technician. To interchange the heating factor, you will first want to collect the required instruments and supplies, together with a brand new heating factor, screwdriver, and pliers. Upon getting the required objects, observe these steps to switch the heating factor in your Samsung dryer.
First, unplug the dryer from the facility outlet and take away the again panel of the dryer. Subsequent, find the heating factor and disconnect the wires which might be hooked up to it. Then, take away the previous heating factor from the dryer. To put in the brand new heating factor, merely insert it into the dryer and reconnect the wires. Lastly, exchange the again panel of the dryer and plug it again into the facility outlet. Your Samsung dryer ought to now be working correctly.
In case you are not assured in your capacity to switch the heating factor your self, it’s best to contact a professional equipment restore technician. A professional technician will have the ability to shortly and safely exchange the heating factor in your Samsung dryer and get it working correctly once more.
Security Precautions
Earlier than embarking on the duty of changing the heating factor in your Samsung dryer, it’s crucial to prioritize your security. Electrical energy and heating components can pose vital dangers if correct precautions will not be taken. To make sure a secure and profitable restore, meticulously adhere to the next security measures:
1. Disconnect the Energy Supply
The primary and most vital step is to disconnect {the electrical} provide to your dryer. That is a necessary security measure to stop any unintentional electrical shocks or fires. Find the principle electrical panel in your house and swap off the circuit breaker or take away the fuse equivalent to the dryer. Confirm that the facility has certainly been disconnected by testing the dryer outlet with a voltage tester. Wait a couple of minutes to permit any residual electrical energy within the system to dissipate.
| Suggestions for Disconnecting the Energy Supply |
|---|
| – Determine the proper circuit breaker or fuse for the dryer. |
| – Swap off the corresponding circuit breaker or take away the fuse. |
| – Use a voltage tester to substantiate that the outlet is not receiving energy. |
| – Enable enough time for the residual electrical energy to dissipate. |
Collect Essential Instruments and Supplies
Earlier than embarking on the restore, it is essential to collect the important instruments and supplies. Here is an in depth rundown of what you will want:
Supplies:
- New heating factor
- Electrical tape
- Warmth-resistant gloves (non-compulsory)
Instruments:
| Software | Function |
|---|---|
| Phillips-head screwdriver | Take away the screws securing the entry panels and heating factor |
| Torx screwdriver | Unscrew the bolts holding the heating factor in place (some fashions) |
| Multimeter | Check the continuity of the heating factor (non-compulsory) |
| Pliers (non-compulsory) | Tighten or loosen nuts or bolts |
| Protecting goggles (non-compulsory) | Defend eyes from unfastened particles |
Extra Supplies:
Whereas not strictly vital, sure supplies could make the restore course of smoother:
- Flashlight: Illuminate the work space, particularly in dimly lit areas
- Store towels or rags: Clear up any particles or spills
- Digicam: Doc the disassembly course of for simpler reassembly
- Warmth gun (non-compulsory): Soften previous adhesive or velocity up evaporation of moisture
- Soldering iron (non-compulsory): Restore broken wires or safe new connections
Find and Take away the Rear Panel
Unplug the dryer and transfer it away from the wall.
For security functions, unplug your dryer from the facility outlet earlier than beginning any repairs. It could even be greatest to tug the dryer away from the wall to provide your self ample area to work.
Find the screws holding the rear panel in place.
Figuring out the screws that maintain the rear panel of the dryer is essential. These screws are usually situated across the perimeter of the panel, and their place might range barely relying on the dryer mannequin. Upon getting recognized the screws, proceed to the following step.
Take away the screws and thoroughly raise off the rear panel.
Upon getting situated the screws, use a screwdriver to take away them. Watch out to not strip the screws or harm the rear panel when eradicating them. After eradicating all of the screws, rigorously raise the rear panel off the dryer. Observe that the rear panel could also be barely heavy, so make sure you assist it with one hand whereas eradicating the screws with the opposite.
Disconnect Present Heating Factor
**Step 1: Unplug the Dryer**
Earlier than engaged on the dryer, disconnect it from the facility provide by unplugging it from the wall outlet.
**Step 2: Take away the Again Panel**
Find the screws on the again panel of the dryer and take away them utilizing a screwdriver. Rigorously raise and take away the again panel to reveal the internal parts.
**Step 3: Disconnect Wires**
Determine the 2 wires linked to the heating factor terminals. Gently pull the wire connectors off the terminals. Make notice of which wire goes to which terminal for future reference.
**Step 4: Take away the Heating Factor**
The heating factor is held in place by two screws or bolts. Use a wrench or socket to loosen and take away these fasteners. Rigorously slide the heating factor out of its housing. Be conscious of sharp edges and keep away from touching the factor together with your naked palms.
| Screw/Bolt Location | Removing Methodology |
|---|---|
| High of the housing | Loosen with a wrench or socket |
| Backside of the housing | Take away with a wrench or socket |
**Step 5: Examine the Heating Factor**
Visually examine the heating factor for any harm or corrosion. If the factor is broken, it’s going to should be changed earlier than reassembling the dryer.
Take away Previous Heating Factor
5. Disconnect the heating factor from the facility provide.
| Sort of Dryer | Steps |
|---|---|
| Fuel Dryer |
Shut off the fuel provide to the dryer earlier than continuing. |
| Electrical Dryer |
Unplug the dryer from the facility outlet and switch off the circuit breaker or fuse for the dryer circuit |
6. Take away the screws that maintain the heating factor in place.
7. Unclip the wire terminals from the heating factor.
8. Pull the heating factor out of the dryer.
Set up New Heating Factor
Security Precautions
Earlier than starting any work, unplug your dryer and disconnect the facility supply. Make sure that the machine is cool to the contact.
Eradicating the Previous Heating Factor
- Take away the entrance panel of the dryer by unscrewing the screws on the high and pulling it ahead.
- Find the entry panel on the entrance of the dryer’s drum. Take away the screws and pull it open.
- Pull the previous heating factor unit in direction of you to disconnect the wires.
- Unplug the wires from {the electrical} terminals and take away the previous heating factor.
Putting in the New Heating Factor
- Insert the brand new heating factor unit into the opening within the drum.
- Join the wires to {the electrical} terminals. Make sure that the connections are safe.
- Push the heating factor unit again into place and safe it with the screws.
- Reattach the entry panel and the entrance panel of the dryer.
- Plug the dryer again into the facility outlet and switch it on to check the brand new heating factor.
Suggestions for Troubleshooting
| Downside | Resolution |
|---|---|
| Dryer not heating | Examine the facility provide. Examine the wires and connections to the heating factor. Check the heating factor with a multimeter. |
| Dryer overheating | Unplug the dryer and let it settle down. Clear the lint filter and exhaust vent. Examine the thermostat and temperature sensor. |
Reconnect Electrical Wires
Now it is time to reconnect {the electrical} wires to the heating factor. You should definitely match the wires to the proper terminals on the factor. Usually, the crimson wire will hook up with the left terminal and the white wire will hook up with the appropriate terminal. Nonetheless, consult with your dryer’s particular wiring diagram to substantiate.
Tighten the screws on the terminals securely utilizing a screwdriver. Make sure that the wires are making good contact with the terminals to stop any unfastened connections that might trigger arcing or different electrical points.
As soon as the wires are linked, tuck them again into the insulation across the heating factor. This may assist to guard the wires from warmth harm and maintain the within of the dryer tidy.
Wiring Diagram
For fast reference, here’s a desk with a normal wiring diagram for many Samsung dryers:
| Wire Colour | Terminal |
|---|---|
| Crimson | Left Terminal |
| White | Proper Terminal |
Once more, double-check your dryer’s particular wiring diagram to make sure accuracy earlier than making any connections.
Substitute Rear Panel
Now that the screws are eliminated, raise the rear panel up from the underside and pull it in direction of you to detach it from the dryer. Watch out to not harm any wires or parts as you do that.
As soon as the rear panel is eliminated, you should have entry to the heating factor. The heating factor is situated on the backside of the dryer, behind the drum. It’s held in place by two screws.
Step 8: Take away the Heating Factor’s Wiring
Earlier than eradicating the heating factor, you’ll want to disconnect its wiring. The heating factor has two wires linked to it: a black wire and a white wire. Use a pair of pliers to softly pull the wires off of the heating factor’s terminals.
As soon as the wires are disconnected, you may take away the heating factor. Use a screwdriver to take away the 2 screws that maintain the heating factor in place. As soon as the screws are eliminated, the heating factor could be pulled out of the dryer.
| Step 6: Find the Heating Factor | The heating factor is situated on the backside of the dryer, behind the drum. It’s held in place by two screws. |
| Step 7: Disconnect the Heating Factor’s Wiring | Earlier than eradicating the heating factor, you’ll want to disconnect its wiring. The heating factor has two wires linked to it: a black wire and a white wire. Use a pair of pliers to softly pull the wires off of the heating factor’s terminals. |
| Step 8: Take away the Heating Factor | As soon as the wires are disconnected, you may take away the heating factor. Use a screwdriver to take away the 2 screws that maintain the heating factor in place. As soon as the screws are eliminated, the heating factor could be pulled out of the dryer. |
As soon as the previous heating factor is eliminated, you may exchange it with the brand new one. Insert the brand new heating factor into the dryer and safe it with the 2 screws. You should definitely join the wires to the heating factor’s terminals within the right order: black wire to black terminal, white wire to white terminal.
As soon as the brand new heating factor is put in, you may reattach the rear panel to the dryer. Safe the rear panel with the screws that you just eliminated earlier.
Check the Dryer
Upon getting changed the heating factor, you will need to check the dryer to verify it’s working correctly. Listed below are the steps on the way to check the dryer:
| Step | Motion |
|---|---|
| 1 | Be sure the dryer is plugged into an outlet and that the facility swap is turned on. |
| 2 | Open the dryer door and place a moist towel inside. |
| 3 | Shut the dryer door and choose the “Regular” or “Timed Dry” cycle. |
| 4 | Press the “Begin” button to start out the dryer. |
| 5 | Let the dryer run for a couple of minutes to see if the towel will get heat. |
| 6 | If the towel will get heat, then the heating factor is working correctly. |
| 7 | If the towel doesn’t get heat, then there could also be an issue with the heating factor or different parts of the dryer. |
In case you are having issues together with your dryer, it’s best to contact a professional equipment restore technician for help.
Security Precautions Earlier than Beginning:
1. Unplug the dryer from the facility outlet and permit it to chill fully.
2. Put on gloves to guard your palms from sharp edges.
3. Collect all vital instruments and elements earlier than beginning.
Checking the Heating Factor:
1. Take away the again panel of the dryer by unscrewing the screws across the perimeter.
2. Find the heating factor, which is usually an oblong steel field with two wires linked to it.
3. Unplug the wires from the heating factor utilizing needle-nose pliers.
Eradicating the Heating Factor:
1. Unscrew the nuts holding the heating factor in place.
2. Rigorously raise the heating factor out of the dryer cupboard.
Putting in the New Heating Factor:
1. Place the brand new heating factor into the dryer cupboard.
2. Tighten the nuts holding the heating factor in place.
3. Join the wires to the heating factor.
Troubleshooting Suggestions
1. If the dryer nonetheless doesn’t warmth, test the thermal fuse.
2. If the thermal fuse is blown, exchange it.
3. If the heating factor shouldn’t be getting energy, test the wiring.
4. If the wiring is broken, restore or exchange it.
5. If the dryer remains to be not heating, contact a professional equipment restore technician.
Extra Troubleshooting Suggestions:
| Attainable Trigger | Resolution |
|---|---|
| Unfastened belt | Regulate or exchange the belt |
| Vent blockage | Clear the dryer vent |
| Defective thermostat | Substitute the thermostat |
| Defective relay | Substitute the relay |
| Defective management board | Substitute the management board |
7. If the dryer is making a loud noise, test the drum bearings.
8. If the drum bearings are worn, exchange them.
9. If the dryer is shaking excessively, test the shock absorbers.
10. If the shock absorbers are worn, exchange them.
How one can Set up a Heating Factor in a Samsung Dryer
Changing the heating factor in a Samsung dryer is a comparatively easy job that may be accomplished in about an hour. Nonetheless, you will need to take security precautions and observe the directions rigorously to keep away from harm or harm to the dryer.
Supplies wanted:
- New heating factor
- Screwdriver
- Wrench
- Security glasses
- Gloves
Directions:
- Unplug the dryer from the facility outlet.
- Placed on security glasses and gloves.
- Take away the again panel of the dryer by unscrewing the screws that maintain it in place.
- Find the heating factor, which is normally situated on the backside of the dryer.
- Disconnect the wires from the heating factor.
- Unscrew the bolts that maintain the heating factor in place.
- Raise the heating factor out of the dryer.
- Place the brand new heating factor into the dryer.
- Screw within the bolts to safe the heating factor in place.
- Join the wires to the heating factor.
- Substitute the again panel of the dryer.
- Plug the dryer again into the facility outlet.
