Putting in jigsaw blades on DeWalt 20-volt jigsaws could be a breeze! This is a step-by-step information that will help you get it achieved rapidly and effectively. Start by making certain that your jigsaw is off and the battery is disconnected. It is essential to work on a cooled-down jigsaw to forestall any burns.
Find the blade ejection lever on the entrance of the noticed. It’s sometimes a small, spring-loaded lever. Push the lever away from you and concurrently pull down the blade clamp. It will let you clear the trail for the brand new blade. Subsequent, align the brand new blade’s enamel dealing with downwards and insert it into the blade clamp. Rigorously push the blade up till it’s securely held in place. Launch the blade clamp by pushing it in direction of you and lock the blade in place by participating the blade ejection lever again into its unique place. Make sure the blade is firmly seated by gently pulling on it.
Lastly, reconnect the battery and activate the jigsaw. Check the blade by making a couple of cuts on a scrap piece of wooden. If the blade cuts easily with none wobbling or vibration, you’ve got efficiently put in the blade. Bear in mind, it is indispensable to put on gloves and security glasses all through the method in your safety.
Disassembling the Jigsaw
Earlier than you may insert a brand new blade into your DeWalt 20V jigsaw, you could first disassemble the software. Observe these steps to take action safely and effectively:
1. Unplug the Jigsaw
In the beginning, it’s essential to unplug the jigsaw from the facility supply. This security precaution prevents unintended activation whereas disassembling the software. Find the facility twine and disconnect it on the plug.
As soon as the jigsaw is unplugged, you may proceed to the following steps.
2. Take away the Shoe Insert
The shoe insert is a small, detachable piece situated on the bottom of the jigsaw. To take away it, merely grasp the insert together with your fingers or a pair of pliers and pull it straight out. It will expose the blade clamp mechanism under.
3. Open the Blade Clamp
With the shoe insert eliminated, you will notice a metallic blade clamp. To open the clamp, find the lever or knob on the facet of the jigsaw and rotate it counterclockwise. It will loosen the clamp and let you insert or take away the jigsaw blade safely.
4. Take away the Outdated Blade
As soon as the blade clamp is open, you may take away the previous blade. Grip the blade firmly with one hand and gently pull it straight up out of the clamp. If the blade is caught, chances are you’ll want to make use of a pair of pliers or a screwdriver to assist pry it unfastened.
Inserting the New Blade
As soon as you have chosen the suitable blade in your mission, it is time to insert it into the jigsaw. This is an in depth step-by-step information:
Step 1: Take away the Base Plate
Loosen the screws holding the bottom plate in place utilizing an Allen key or wrench. Rigorously raise off the bottom plate to show the blade clamp.
Step 2: Open the Blade Clamp
Find the lever or dial that releases the blade clamp. Press or flip the discharge mechanism to open the clamp and permit the insertion of the brand new blade.
Step 3: Insert the Blade
Align the enamel of the brand new blade with the information slots on the blade clamp. Insert the blade into the clamp making certain that the enamel are dealing with within the right route. The blade needs to be inserted with the enamel pointing downward for chopping on the upstroke and upward for chopping on the downstroke.
| Chopping Course | Tooth Orientation |
|---|---|
| Upstroke (Chopping on the best way up) | Tooth dealing with downward |
| Downstroke (Chopping on the best way down) | Tooth dealing with upward |
Tip: Should you’re uncertain of the right enamel orientation, seek the advice of your jigsaw’s guide or test the producer’s web site for particular steerage.
Step 4: Shut the Blade Clamp
As soon as the blade is inserted, press or flip the discharge mechanism once more to shut the blade clamp. Be certain that the blade is securely held in place with none wobble.
Step 5: Reattach the Base Plate
Place the bottom plate again onto the jigsaw and tighten the screws to safe it. Your new jigsaw blade is now put in and prepared to be used.
Securing the Blade
4. Tightening the Blade: A Complete Information
As soon as the blade is seated accurately, it is essential to tighten it securely. Use the supplied wrench or key to carry the retaining bolt nonetheless whilst you flip the nut clockwise utilizing the opposite hand. Guarantee you’ve got a agency grip and apply sufficient power to snugly fasten the blade, however keep away from overtightening as it might warp or harm the blade. To make sure correct tightness, use a torque wrench set to the producer’s really helpful torque specification. Nevertheless, if you happen to’re working and not using a torque wrench, goal for a cosy match that permits the blade to maneuver freely with out extreme play.
| Tip | Rationalization |
|---|---|
| Safe the blade firmly, however do not overtighten | Overtightening can warp or harm the blade |
| Use a torque wrench for exact tightening | Ensures correct tightness with out damaging the blade |
| Goal for a cosy match with out extreme play | Permits the blade to maneuver freely throughout chopping |
Adjusting Blade Pressure
As soon as you have inserted the blade, you may want to regulate the blade rigidity to make sure it is held securely. Most DeWalt jigsaws have a tool-less blade rigidity lever or knob that means that you can simply modify the strain with out the necessity for a hex key or different instruments. This is find out how to modify the blade rigidity:
- Establish the blade rigidity adjustment lever or knob in your particular DeWalt jigsaw mannequin.
- Maintain the lever or knob and switch it counterclockwise to loosen the blade rigidity.
- Insert the blade into the jigsaw and tighten the lever or knob clockwise till the blade is held firmly in place.
- Check the blade rigidity by gently pulling on the blade. It ought to really feel comfortable however not overly tight.
- If the blade strikes too simply or rattles, tighten the strain lever or knob additional. If the blade is just too tight, it might bind or break throughout operation, so loosen the strain barely.
Ideas for Adjusting Blade Pressure
- Completely different blades could require completely different rigidity settings. Thinner blades typically require much less rigidity than thicker blades.
- At all times test the blade rigidity earlier than every use to make sure it is safe and correctly adjusted.
- Keep away from overtightening the blade rigidity, as this may harm the blade or the jigsaw mechanism.
Security Precautions
1. Put on Security Gear: At all times put on eye safety, gloves, and a mud masks when working with energy instruments.
2. Unplug Energy Device: Earlier than performing any upkeep or changes, be sure that the jigsaw is unplugged from the facility supply.
3. Examine Blade: Verify the blade for any harm or put on earlier than set up. Don’t use a broken blade.
4. Hold Away from Blade: Hold your palms and fingers away from the blade space whereas the jigsaw is working.
5. Securely Clamp Workpiece: Safe the workpiece firmly earlier than beginning to reduce. It will forestall the fabric from shifting through the chopping course of.
6. Keep away from Kickbacks: Keep a agency grip on the jigsaw and use each palms to regulate the software. Keep away from chopping into supplies which can be too thick or exhausting, as this may trigger kickbacks.
7. Use Right Blade: Select the right blade for the fabric you might be chopping. Incorrect blade choice can result in ineffective chopping and potential hazards.
8. Observe Producers’ Directions: Confer with the producer’s directions for particular security tips and upkeep procedures.
9. Extra Precautions for 20 Volt DeWalt Jigsaws:
- Take away Battery Earlier than Altering Blade: At all times take away the battery from the jigsaw earlier than altering the blade.
- Find Blade Clamp Lever: Establish the blade clamp lever on the jigsaw, normally situated close to the blade housing.
- Pull Up Clamp Lever: Pull up the blade clamp lever to launch the blade.
- Take away Outdated Blade: Grip the previous blade firmly with gloved palms and pull it straight out of the blade holder.
- Insert New Blade: Align the brand new blade with the blade holder and insert it securely.
- Safe Blade: Push down on the blade clamp lever to safe the brand new blade in place.
- Examine Blade Set up: Be certain that the blade is correctly put in and securely mounted earlier than persevering with.
Putting in Dewalt Jigsaw Blades 20 Volt
Step 1: Collect Supplies
You have to a Dewalt jigsaw, a Dewalt 20V jigsaw blade, and a Phillips head screwdriver.
Step 2: Put together the Jigsaw
Take away the battery from the jigsaw and insert the jigsaw blade into the blade clamp.
Step 3: Tighten the Blade Clamp
Use the Phillips head screwdriver to tighten the blade clamp screw till the blade is securely held.
Step 4: Reattach the Battery
Reattach the battery to the jigsaw.
Step 5: Check the Blade
Activate the jigsaw and make a couple of take a look at cuts to make sure the blade is put in accurately and chopping easily.
Troubleshooting Ideas
1. The blade shouldn’t be chopping straight
Verify if the blade is put in accurately and if the blade clamp is tight. If the issue persists, attempt a brand new blade.
2. The blade is vibrating excessively
Verify if the blade is bent or broken. Whether it is, substitute the blade. Additionally, test if the jigsaw is balanced correctly and if the blade clamp is tight.
3. The blade shouldn’t be chopping by way of the fabric
Verify if the blade is sharp and if the jigsaw is ready to the right pace for the fabric being reduce. If the issue persists, attempt a unique blade.
4. The jigsaw is overheating
Cease utilizing the jigsaw and let it settle down. Verify if the blade is caught or if the jigsaw is clogged with sawdust. Clear the jigsaw and take a look at utilizing a brand new blade.
5. The jigsaw is making unusual noises
Cease utilizing the jigsaw and test if there are any unfastened components or broken elements. Should you discover any issues, contact a certified restore technician.
6. The jigsaw shouldn’t be beginning
Verify if the battery is charged and if the jigsaw is correctly plugged into an outlet. If the issue persists, attempt a unique battery or contact a certified restore technician.
7. The jigsaw shouldn’t be responding to the set off
Verify if the set off is caught or broken. Whether it is, contact a certified restore technician.
8. The jigsaw is smoking
Cease utilizing the jigsaw instantly and unplug it from the outlet. Contact a certified restore technician.
9. The jigsaw is leaking oil
Cease utilizing the jigsaw and speak to a certified restore technician.
10. The jigsaw shouldn’t be lined by the guarantee
If the jigsaw shouldn’t be lined by the guarantee, you may contact a certified restore technician. They’ll diagnose the issue and supply a value estimate for the repairs.
How To Set up Dewalt Jigsaw Blades 20 Volt
Putting in Dewalt jigsaw blades on a 20-volt jigsaw is a straightforward course of that may be accomplished in a couple of minutes. Listed here are the steps it is advisable to comply with:
- Flip off the jigsaw and unplug it from the facility supply. That is necessary for security causes.
- Open the blade clamp. To do that, push the lever or button that’s situated on the facet of the jigsaw. The blade clamp will open, permitting you to take away the previous blade.
- Take away the previous blade. Grip the previous blade together with your fingers and pull it straight out of the blade clamp.
- Insert the brand new blade. Align the brand new blade with the blade clamp and insert it into the clamp. Guarantee that the enamel of the blade are dealing with within the right route.
- Shut the blade clamp. Push the lever or button that you just used to open the blade clamp. The blade clamp will shut, securing the brand new blade in place.
- Plug within the jigsaw and switch it on. Your jigsaw is now prepared to make use of.
Folks Additionally Ask About How To Set up Dewalt Jigsaw Blades 20 Volt
What’s one of the simplest ways to chop a straight line with a jigsaw?
To chop a straight line with a jigsaw, use a straight edge as a information. Place the straight edge alongside the road you wish to reduce and maintain it firmly in place. Then, begin chopping alongside the road, maintaining the jigsaw in opposition to the straight edge.
What’s one of the simplest ways to chop a curve with a jigsaw?
To chop a curve with a jigsaw, use a freehand approach. Begin by chopping alongside the surface fringe of the curve. Then, step by step transfer the jigsaw in direction of the within fringe of the curve, ensuring to maintain the blade perpendicular to the floor of the fabric.
What’s one of the simplest ways to chop a gap with a jigsaw?
To chop a gap with a jigsaw, first drill a pilot gap within the middle of the opening. Then, insert the jigsaw blade into the pilot gap and begin chopping. Hold the jigsaw perpendicular to the floor of the fabric and step by step transfer the jigsaw across the circumference of the opening.
