Reworking your kitchen is an excellent method of enhancing the aesthetic attraction and performance of your house. Among the many numerous upgrades that you could make, putting in crown molding on kitchen cupboards stands out as a very efficient strategy to elevate the general design. The subtle and stylish contact of crown molding provides a contact of refinement to your kitchen house, turning it into a classy and welcoming space.
Putting in crown molding on kitchen cupboards is a comparatively simple activity that requires minimal carpentry expertise and may be accomplished in just a few easy steps. By following a step-by-step information and utilizing the proper instruments and supplies, you possibly can obtain professional-looking outcomes with out the necessity for hiring knowledgeable. The transformation that crown molding brings to your kitchen is really exceptional, and the sense of accomplishment you will really feel after finishing the challenge your self is an added bonus.
Earlier than embarking on this challenge, it is important to collect all the required instruments and supplies. You may want a miter noticed, a nail gun, a stage, wooden filler, a caulk gun, and quite a lot of nails and caulk. Upon getting all the things you want, you possibly can start by measuring and slicing the crown molding to the suitable lengths. At all times make sure that your cuts are exact and correct to make sure a seamless match.
Gathering Mandatory Supplies and Instruments
Supplies:
- Crown molding
- Adhesive or brad nails
- Filler (elective)
- Paint or stain (elective)
Instruments:
| Software | Goal |
|---|---|
| Miter noticed | Slicing the molding to the proper angles |
| Brad nailer | Securing the molding to the cupboards |
| Measuring tape | Measuring and marking the molding |
| Caulk gun | Filling any gaps between the molding and the cupboards (elective) |
| Sandpaper | Smoothing any tough edges or transitions (elective) |
| Paintbrush or curler | Making use of paint or stain to the molding (elective) |
Measuring and Marking the Crown Molding
1. Decide the General Size
Measure the entire size of the cupboard run the place you propose to put in the crown molding. Add 12 inches to account for miter cuts on every finish. For instance, if the cupboard run is 10 toes (120 inches), you would wish 132 inches (120 + 12) of molding.
2. Measure and Minimize the Crown Molding
a. Miter Cuts for Outdoors Corners
* Mark the molding on the desired size minus 1 inch.
* Maintain a miter noticed at a 45-degree angle and lower the molding on the marked line.
* The lower ought to produce a 45-degree angle to facilitate a clean miter joint on the exterior nook.
b. Miter Cuts for Inside Corners
* Mark the molding on the desired size minus 1 inch.
* Maintain a miter noticed at a 45-degree angle and lower the molding backward from the marked line.
* The lower ought to produce a 45-degree mirrored angle to create a cosy match within the inside nook.
c. Dry Becoming and Changes
* Dry match the crown molding segments collectively to make sure correct alignment.
* Use a pencil to mark any areas that have to be trimmed or adjusted for a good match.
* Repeat the slicing and dry becoming course of till the crown molding items match collectively seamlessly.
| Outdoors Nook | Inside Nook |
|---|---|
| Minimize at 45 levels | Minimize backward at 45 levels |
Putting in the Crown Molding on the Wall Cupboards
As soon as the crown molding is lower and fitted to the wall, it is time to set up it on the cupboards. Begin by making use of a bead of building adhesive to the again of the molding, then press it into place on the cupboard. Use a nail gun to safe the molding with 1 1/4-inch brad nails, spacing them about 6 inches aside. Be sure you countersink the nails barely so they do not protrude from the floor of the molding.
Coping Crown Molding
When putting in crown molding on the within corners of your cupboards, you will must cope the molding in order that the 2 items match collectively seamlessly. To do that, you will want a coping noticed or a miter noticed with a coping sled attachment.
To manage crown molding utilizing a coping noticed, you will must:
- Measure and mark the size of the molding you want.
- Minimize the molding to size utilizing a miter noticed.
- Lay the molding in your workbench with the highest edge going through up.
- Use a coping noticed to chop a collection of small notches alongside the underside fringe of the molding, beginning about 1/4 inch from the top and dealing your method in direction of the middle. The notches must be about 1/8 inch deep and spaced about 1/4 inch aside.
- As soon as you have lower the entire notches, use a chisel to take away the surplus wooden from between them.
- Check the match of the molding by holding it as much as the cupboard nook. The molding ought to match snugly with none gaps.
- If the match shouldn’t be excellent, you may make changes by fastidiously slicing away extra wooden with the coping noticed or chisel.
To manage crown molding utilizing a miter noticed with a coping sled attachment, you will must:
- Measure and mark the size of the molding you want.
- Minimize the molding to size utilizing a miter noticed.
- Connect the coping sled to your miter noticed.
- Lay the molding on the coping sled with the highest edge going through up.
- Use the coping sled to information the noticed as you narrow a collection of small notches alongside the underside fringe of the molding, beginning about 1/4 inch from the top and dealing your method in direction of the middle. The notches must be about 1/8 inch deep and spaced about 1/4 inch aside.
- As soon as you have lower the entire notches, use a chisel to take away the surplus wooden from between them.
- Check the match of the molding by holding it as much as the cupboard nook. The molding ought to match snugly with none gaps.
- If the match shouldn’t be excellent, you may make changes by fastidiously slicing away extra wooden with the coping noticed or chisel.
Putting in the Crown Molding on the Base Cupboards
Upon getting your entire supplies and instruments assembled, you possibly can start putting in the crown molding on the bottom cupboards. Listed below are the steps:
1. Measure and Minimize the Crown Molding
Measure the size of the again of the cupboard. Minimize a chunk of crown molding to that size. If you might want to lower a miter joint, use a miter noticed.
2. Apply Adhesive to the Crown Molding
Apply a bead of adhesive to the again of the crown molding. Use a caulk gun to use the adhesive evenly.
3. Place the Crown Molding
Place the crown molding on the again of the cupboard, aligning the underside fringe of the molding with the highest fringe of the cupboard. Press the molding into place, making certain that the adhesive is making contact with the cupboard.
4. Safe the Crown Molding
Hammer small nails via the face of the crown molding into the cupboard. House the nails about 6 inches aside. Countersink the nails with a nail set.
5. Fill Nail Holes and Paint
Fill the nail holes with wooden filler. Enable the wooden filler to dry fully. Sand the wooden filler clean. Paint the crown molding to match the cupboards.
| Software | Goal |
|---|---|
| Miter noticed | To chop miter joints within the crown molding |
| Caulk gun | To use adhesive to the crown molding |
| Hammer | To safe the crown molding to the cupboard |
| Nail set | To countersink the nails |
| Wooden filler | To fill the nail holes |
| Sandpaper | To clean the wooden filler |
| Paint | To color the crown molding to match the cupboards |
Nailing and Gluing the Crown Molding in Place
Now that your crown molding is lower and fitted, it is time to nail and glue it in place. This can be a comparatively easy course of, but it surely’s necessary to take your time and do it fastidiously to make sure a professional-looking end.
To nail the crown molding, use a 1-1/2-inch brad nailer or 2-inch ending nails. Drive the nails via the face of the molding into the highest of the cupboard body. Be sure you countersink the nails barely in order that they do not present via the paint or end.
As soon as the crown molding is nailed in place, apply a bead of wooden glue to the again of the molding and press it firmly into place. Use a moist fabric to wipe away any extra glue that squeezes out.
To make sure a safe maintain, it’s possible you’ll need to clamp the crown molding in place for a number of hours whereas the glue dries. As soon as the glue is dry, you possibly can take away the clamps and revel in your new crown molding!
Listed below are some extra suggestions for nailing and gluing crown molding:
Use a brad nailer or ending nails.
Brad nails are thinner and fewer seen than ending nails. Nonetheless, ending nails are stronger and supply a safer maintain. In the event you’re utilizing a brad nailer, you’ll want to use nails which are lengthy sufficient to penetrate via the molding and into the cupboard body.
Countersink the nails.
Countersinking the nails will assist to cover them from view. To countersink a nail, use a nail set to drive the nail barely beneath the floor of the molding.
Apply a bead of wooden glue to the again of the molding.
Wooden glue will assist to create a robust bond between the molding and the cupboard body. Be sure you apply the glue evenly to all the floor of the molding.
Clamp the molding in place.
Clamping the molding in place will assist to make sure a safe maintain whereas the glue dries. Use clamps which are massive sufficient to span all the width of the molding.
Here’s a desk summarizing the steps for nailing and gluing crown molding:
| Step | Directions |
|---|---|
| 1 | Minimize the crown molding to size. |
| 2 | Match the crown molding to the cupboard body. |
| 3 | Nail the crown molding in place. |
| 4 | Apply a bead of wooden glue to the again of the molding. |
| 5 | Press the molding firmly into place. |
| 6 | Wipe away any extra glue. |
| 7 | Clamp the molding in place for a number of hours whereas the glue dries. |
Filling and Sanding Nail Holes
As soon as the crown molding is secured, it is important to hide the nail holes for a seamless end.
Supplies:
- Wooden filler
- Putty knife
- Sandpaper (150-grit and 220-grit)
- Tack fabric
Steps:
1.
Apply a skinny layer of wooden filler to every nail gap utilizing the putty knife. Easy over the holes making certain they’re fully stuffed.
2.
Enable the wooden filler to dry in keeping with the producer’s directions. Drying occasions might differ.
3.
As soon as dry, sand the stuffed areas utilizing 150-grit sandpaper to take away extra filler and clean the floor.
4.
Change to wonderful 220-grit sandpaper for additional smoothing and mixing the stuffed areas with the encircling wooden.
5.
Wipe away any sanding mud utilizing a tack fabric earlier than portray or staining.
Extra Suggestions:
For an ideal match, use wooden filler particularly designed for the kind of wooden your cupboards are product of.
For bigger nail holes, apply a number of skinny layers of wooden filler, permitting every layer to dry earlier than sanding. This prevents shrinkage and cracking.
If the wooden filler begins to sag earlier than drying, gently press it again into the opening utilizing a toothpick or the sting of the putty knife.
After sanding, examine the stuffed areas beneath completely different lighting circumstances to make sure they’re fully blended and invisible.
Priming and Portray the Crown Molding
As soon as the crown molding is fitted and secured, it is time to prime and paint it. Listed below are the steps to make sure a professional-looking end:
Priming the Molding
Use a high-quality wooden primer that’s suitable along with your paint. Apply a skinny, even coat to all the molding utilizing a brush or curler. Enable the primer to dry fully earlier than transferring on to the subsequent step.
Making use of the Paint
Select a paint that enhances your kitchen cupboards and different cabinetry. Apply two skinny, even coats of paint to the molding, permitting every coat to dry totally earlier than making use of the subsequent. Use a fine-bristle brush for detailed areas and a curler for bigger surfaces.
Ending Touches
As soon as the paint is totally dry, you possibly can add the ending touches to your crown molding:
- Caulk the Joints: Apply a skinny bead of caulk to the seams between the molding and the cupboards. Use a caulk gun and a clean software to use the caulk evenly.
- Contact Up: Examine the molding for any imperfections or areas that want touching up. Use a small brush and contact up these areas with the matching paint coloration.
- Seal the Molding: Apply a transparent polyurethane end to guard the molding and improve its shine. Use a gentle brush or fabric to use the polyurethane evenly.
Portray Strategies for Intricate Crown Molding
For crown molding with intricate particulars, use the next strategies for a flawless end:
| Method | Description |
|---|---|
| Dry Brush Method: | Load a dry brush with a small quantity of paint and gently brush over the raised areas of the molding to spotlight the small print. |
| Glazing: | Apply a skinny glaze over the paint so as to add depth and dimension to the small print. |
| Highlighting: | Use a light-colored paint to spotlight the raised areas of the molding, making a extra ornate look. |
How To Set up Crown Molding On Kitchen Cupboards
Listed below are the steps on set up crown molding on kitchen cupboards:
- Measure and lower the crown molding. Measure the size of the cupboard and lower the crown molding to dimension. Use a miter noticed to chop the molding at a 45-degree angle.
- Connect the crown molding to the cupboard. Apply a bead of building adhesive to the again of the crown molding and press it into place on the cupboard. Use a brad nailer to safe the molding to the cupboard.
- Fill the nail holes. Fill the nail holes with wooden filler and permit it to dry. Sand the wooden filler clean as soon as it’s dry.
- Paint or stain the crown molding. Paint or stain the crown molding to match the cupboards or the remainder of the kitchen décor.
Folks Additionally Ask About How To Set up Crown Molding On Kitchen Cupboards
What’s crown molding?
Crown molding is an ornamental molding that’s put in on the high of a wall or cupboard. It’s used so as to add a of completion to a room and to create a extra elegant look.
How do I select the proper crown molding for my kitchen cupboards?
When selecting crown molding on your kitchen cupboards, contemplate the type of your cupboards and the general décor of your kitchen. You may select from quite a lot of profiles and sizes of crown molding to search out the proper match on your kitchen.
How do I lower crown molding at a 45-degree angle?
To chop crown molding at a 45-degree angle, use a miter noticed. Set the noticed to a 45-degree angle and thoroughly lower the molding. Be sure you put on security glasses when utilizing an influence noticed.
How do I connect crown molding to cupboards?
To connect crown molding to cupboards, apply a bead of building adhesive to the again of the molding and press it into place on the cupboard. Use a brad nailer to safe the molding to the cupboard.
