Upgrading your lavatory’s aesthetics or performance usually includes tackling plumbing initiatives, and putting in a brand new tub drain is one such activity. Whether or not you are changing a worn-out drain or customizing your tub’s look, putting in a drain is a manageable DIY undertaking with the fitting instruments and know-how. This complete information will give you step-by-step directions, making certain a seamless set up that leaves your tub trying refreshed and functioning optimally.
Earlier than embarking on the set up course of, collect the required instruments and supplies. You may want a brand new tub drain meeting, a plumber’s putty, a putty knife, an adjustable wrench, a screwdriver, and a flashlight. After you have every part you want, guarantee the bath is empty and the water provide is shut off. Security must be paramount, so put on gloves and eye safety throughout the set up.
With preparation full, the set up can begin. Start by eradicating the previous drain meeting. Use the adjustable wrench to loosen the drain flange and carry it off. Clear the drainpipe opening totally, eradicating any particles or previous putty. Apply a beneficiant bead of plumber’s putty across the base of the brand new drain flange and punctiliously place it over the drainpipe opening. Tighten the flange utilizing the wrench, making certain it is safe however not overtightened. Lastly, set up the drain stopper and overflow plate, and also you’re all set! Double-check for any leaks by operating water into the bathtub and inspecting the drain for correct drainage.
Gathering Essential Supplies
To start your tub drain set up, you may want to collect the required supplies. This is an in depth checklist to make sure you have every part you want readily available:
Instruments
| Qty. | Instrument |
|---|---|
| 1 | Adjustable wrench or channel-type pliers |
| 1 | Phillips screwdriver |
| 1 | Flathead screwdriver |
| 1 | Putty knife |
| 1 | Plumber’s putty |
| 1 | Rags or paper towels |
Supplies
| Qty. | Half |
|---|---|
| 1 | Tub drain meeting (contains stopper and flange) |
| 2 | Washers (often included with tub drain meeting) |
| 1 | Tub drain gasket (if not already put in on tub drain meeting) |
Eradicating the Outdated Drain
Step 1: Begin by eradicating the drain cowl and the strainer. Use a screwdriver or pliers to softly pry the drain cowl off, being cautious to not harm it.
Step 2: As soon as the drain cowl is eliminated, you will notice the drain flange. The drain flange is the steel piece that connects the drain to the bathtub. Unscrew the drain flange by turning it counterclockwise. If the flange is simply too tight to take away by hand, you should utilize a wrench.
Step 3: As soon as the drain flange is eliminated, you will notice the drain pipe. The drain pipe is the pipe that carries water from the bathtub to the drain. Unscrew the drain pipe by turning it counterclockwise. If the pipe is simply too tight to take away by hand, you should utilize a wrench.
| Step | Motion |
|---|---|
| 1 | Take away drain cowl and strainer |
| 2 | Unscrew drain flange |
| 3 | Unscrew drain pipe |
Step 4: As soon as the drain pipe is eliminated, you may take away the previous drain meeting. The previous drain meeting is the steel or plastic piece that’s positioned on the backside of the drain pipe. To take away the previous drain meeting, merely pull it up and out of the drain pipe.
Cleansing the Drain Opening
After you have eliminated the previous drain, you will need to totally clear the drain opening earlier than putting in the brand new one. This can assist to stop leaks and be certain that the brand new drain suits correctly. Listed here are some steps on learn how to clear the drain opening:
Supplies you have to:
| Merchandise | Amount |
|---|---|
| Dry material or paper towels | A number of |
| Scrub brush | 1 |
| Baking soda | 1 cup |
| Vinegar | 1 cup |
1. Wipe away any particles. Use a dry material or paper towels to wipe away any hair, cleaning soap scum, or different particles that could be seen within the drain opening.
2. Scrub the drain opening. Use a scrub brush to clean the drain opening and take away any remaining particles. Make sure to scrub the perimeters of the opening in addition to the underside.
3. Pour baking soda and vinegar down the drain. Pour 1 cup of baking soda down the drain, adopted by 1 cup of vinegar. The baking soda and vinegar will react to create a fizzing motion that can assist to dissolve any remaining particles and disinfect the drain.
4. Let the answer sit for quarter-hour. Enable the baking soda and vinegar answer to take a seat within the drain for quarter-hour to provide it time to work. The fizzing motion will assist to interrupt down any remaining particles.
5. Flush the drain with sizzling water. After quarter-hour, flush the drain with sizzling water to rinse away any remaining baking soda and vinegar answer. The new water will even assist to clear any remaining particles.
6. Examine the drain opening. After you have flushed the drain, examine the drain opening to ensure that it’s clear and freed from particles. If there may be nonetheless particles current, repeat steps 2-5.
Making use of Plumber’s Putty
Earlier than You Start
Collect your supplies: plumber’s putty, a putty knife, and a humid rag.
Steps
1. Clear the Drain Gap
Use a humid rag to take away any grime or particles from the drain gap. This can guarantee a superb seal.
2. Type a Putty Roll
Roll a small quantity of plumber’s putty into a protracted, skinny roll. The roll must be barely longer than the circumference of the drain gap.
3. Place the Putty
Place the putty roll across the drain gap, urgent it firmly into the opening. Use the putty knife to easy the putty out and create a watertight seal.
4. Create a Tapered Edge
Use the putty knife to create a slight taper on the outer fringe of the putty. This can assist forestall water from seeping underneath the seal.
| Tapering the Putty Edge |
|---|
| – Maintain the putty knife at a slight angle to the putty. |
| – Apply agency, even stress whereas pulling the knife in direction of you. |
| – Proceed tapering the putty till it varieties a skinny, watertight seal across the drain gap. |
Putting in the New Drain Meeting
**Step 1: Collect Supplies:** Acquire all needed instruments and gadgets, together with the brand new drain meeting, plumber’s putty, tape, a wrench, and a screwdriver.
**Step 2: Take away the Outdated Drain:** Use a wrench to loosen the nuts holding the drain in place. Gently pull the previous drain meeting out of the bathtub drain gap.
**Step 3: Clear the Drain Gap:** Completely clear the drain gap and floor round it with a sponge or brush to take away any particles or previous sealant.
**Step 4: Apply Plumber’s Putty:** Roll out a rope of plumber’s putty and apply it liberally to the underside of the brand new drain flange. Clean out the putty to create a watertight seal.
**Step 5: Place and Set up the Drain Meeting:**
- Align the drain meeting over the drain gap and gently push it into the opening.
- Tighten the nuts on the underside of the flange by hand till cosy.
- Use a wrench to additional tighten the nuts step by step, alternating between sides to make sure even stress.
**Step 6: Set up the Overflow Plate (Elective):** In case your tub has an overflow drain, set up the overflow plate over the overflow gap utilizing screws or bolts.
**Step 7: Take a look at the Drain:** Run water into the bathtub and examine for any leaks. If a leak happens, tighten the nuts or apply further plumber’s putty to the flange.
Desk: Really useful Instruments and Supplies
| Instrument/Materials | Objective |
|---|---|
| Tub Drain Meeting | New drain meeting |
| Plumber’s Putty | Creates a watertight seal |
| Tape | For momentary sealing or marking |
| Wrench | To tighten nuts |
| Screwdriver | To safe overflow plate (if relevant) |
Tightening the Drain Meeting
As soon as the drain meeting is in place, it is time to tighten it. This can be certain that the seal is watertight and that the drain will perform correctly.
To tighten the drain meeting, you may want a wrench or a pair of pliers. Grip the drain flange with the wrench or pliers and switch it clockwise till it is cosy. Watch out to not overtighten the flange, as this might harm the drain.
As soon as the flange is tight, you may tighten the drain stopper. To do that, merely insert the stopper into the drain gap and switch it clockwise till it is cosy. Once more, watch out to not overtighten the stopper, as this might harm the drain.
This is a extra detailed take a look at the steps concerned in tightening the drain meeting:
| Step | Description |
|---|---|
| 1 | Place the rubber gasket on the drain flange. |
| 2 | Insert the drain flange into the drain gap. |
| 3 | Tighten the drain flange with a wrench or pliers. |
| 4 | Insert the drain stopper into the drain gap. |
| 5 | Tighten the drain stopper by turning it clockwise. |
| 6 | Verify the seal across the drain meeting to verify it is watertight. If needed, tighten the drain flange or drain stopper additional. |
Putting in the Washer
1. Place the washer over the drain opening and align the slots on the washer with the slots on the drain flange.
2. Insert the screws into the slots and tighten them utilizing a screwdriver or a wrench.
3. Apply a bead of plumber’s putty across the base of the washer.
4. Set up the drain cowl over the washer and tighten it.
5. Activate the water and examine for leaks. If there are leaks, tighten the screws or apply extra plumber’s putty.
6. As soon as the washer is put in, you may take a look at it by filling the bathtub with water and permitting it to empty.
7. Troubleshooting Washer Issues
If the washer isn’t draining correctly, there could also be an issue with the washer itself or with the drain. Listed here are some frequent issues and learn how to repair them:
| Downside | Resolution |
|---|---|
| The washer isn’t sealing correctly | Tighten the screws or apply extra plumber’s putty. |
| The drain is clogged | Take away the drain cowl and clear the clog. |
| The drainpipe is kinked or blocked | Straighten the drainpipe or take away the blockage. |
Securing the Overflow Plate
8. Set up the Overflow Plate Gasket
[content] The overflow plate is a skinny, flat steel or plastic piece that covers the overflow gap within the tub. It has a gasket that helps to seal the plate towards the bathtub, stopping water from leaking out.
To put in the overflow plate gasket:
1. Place the gasket on the overflow plate.
2. Heart the gasket over the overflow gap within the tub.
3. Press the gasket firmly into place.
| Tip: |
|---|
| If the gasket isn’t centered, water could leak out across the overflow plate. |
As soon as the gasket is in place, you may safe the overflow plate to the bathtub. To do that, merely insert the screws into the holes within the overflow plate and tighten them till the plate is safe.
Testing the Drain
As soon as the drain is put in, it is important to check it to make sure it is functioning appropriately. This is an in depth information on testing the drain:
1. Fill the Tub with Water
Fill the bathtub with water to a stage slightly below the overflow drain.
2. Open the Drain
Pull the drain plug or open the drain valve to permit water to empty.
3. Observe the Circulate Fee
Monitor the water circulate price. It ought to drain rapidly and easily with none obstructions.
4. Verify for Leaks
Examine the drain for any leaks. Guarantee there isn’t any water seeping from any joints or connections.
5. Pay attention for Noises
Because the water drains, hear for any uncommon noises, comparable to gurgling or hissing. These noises may point out a clog or a difficulty with the plumbing system.
6. Refill the Tub
As soon as the bathtub is empty, refill it with water to check the drain seal.
7. Shut the Drain
Plug the drain or shut the valve to stop water from draining.
8. Wait A number of Hours
Enable the bathtub to take a seat for a number of hours to examine for leaks.
9. Examine the Drain Seal
After ready, examine the drain seal for any water accumulation. If there isn’t any water current, the drain seal is functioning appropriately and there aren’t any leaks.
| Take a look at | End result |
|---|---|
| Circulate price | Fast and easy |
| Leaks | No water seeping |
| Noises | No gurgling or hissing |
| Drain seal | No water accumulation after a number of hours |
Troubleshooting Widespread Issues
1. Water Leaking From the Drain
Verify the drain stopper for correct match and change it if needed.Make sure the drain flange is securely tightened by hand and with a wrench. Re-caulk across the drain flange to stop leaks.
2. Drain Not Draining Correctly
Use a drain snake to take away hair or particles clogging the drain. If the clog persists, disassemble the drain and clear out the parts.
3. Drain is Gurgling
This means a blockage in the primary drain line. Verify different drains in the home for gradual drainage.Contact a plumber to clear the primary drain line.
4. Drain is Making Noises
Free or worn parts could cause rattling or buzzing noises. Tighten or change the free elements, such because the drain stopper or overflow plate.
5. Drain is Overflowing
Verify if the overflow drain is clogged or obstructed. Clear the overflow drain and guarantee it isn’t blocked by particles.
6. Drain is Corroded
Rust or corrosion can result in leaks and harm. Take away the drain and clear it with a vinegar answer. If corrosion is extreme, change the drain.
7. Drain is Free
The drain flange could have loosened over time. Tighten the flange by hand and with a wrench to safe it.
8. Drain is Discolored
Mineral deposits or onerous water can discolor the drain. Clear the drain with a business cleaner or use a vinegar answer to take away discoloration.
9. Drain is Cracked
A cracked drain can result in leaks and must be changed instantly. Contact a plumber or set up a brand new drain your self by following the directions supplied on this article.
10. Drain is Broken Past Restore
If the drain is extensively broken or corroded, it is probably not repairable. On this case, you have to to take away the previous drain and set up a brand new one, following the steps outlined on this article.
How To Set up A Tub Drain
Putting in a bathtub drain is a comparatively easy plumbing undertaking that may be accomplished in a couple of hours. Nevertheless, you will need to observe the steps fastidiously to make sure that the drain is put in correctly and won’t leak. Listed here are the steps on learn how to set up a bathtub drain:
-
Take away the previous drain. To do that, you have to to make use of a pair of pliers to loosen the nuts that maintain the drain in place. As soon as the nuts are free, you may pull the drain out of the bathtub.
-
Clear the drain gap. As soon as the previous drain is eliminated, you have to to wash the drain gap. Use a rag or a sponge to wipe away any particles or grime which will have accrued within the gap.
-
Apply plumbers putty to the brand new drain. Plumbers putty is a sort of sealant that can assist to stop leaks across the drain. Apply a bead of plumbers putty to the underside of the brand new drain.
-
Insert the brand new drain into the drain gap. Align the drain with the drain gap and insert it into the opening. Press down on the drain till it’s seated firmly within the gap.
-
Tighten the nuts. Use a pair of pliers to tighten the nuts that maintain the drain in place. Make sure to tighten the nuts evenly in order that the drain is securely mounted.
-
Take a look at the drain. As soon as the drain is put in, activate the water and examine for leaks. If there are any leaks, you have to to tighten the nuts additional.
Folks Additionally Ask About How To Set up A Tub Drain
What’s the easiest way to wash a bathtub drain?
The easiest way to wash a bathtub drain is to make use of a drain cleaner. Drain cleaners can be found in quite a lot of varieties, together with liquids, gels, and powders. Make sure to observe the instructions on the drain cleaner label fastidiously.
How usually ought to I change my tub drain?
Tub drains must be changed each 5 to 10 years. Nevertheless, you might want to switch the drain sooner if it turns into clogged or broken.
Can I set up a bathtub drain myself?
Sure, you may set up a bathtub drain your self. Nevertheless, you will need to observe the steps fastidiously to make sure that the drain is put in correctly and won’t leak.
