A leaky bathtub faucet with two handles is usually a irritating and annoying drawback. Not solely does it waste water, however it could possibly additionally result in mould and mildew development. In case you’re coping with a leaky faucet, do not despair! With a couple of easy instruments and a little bit little bit of know-how, you possibly can repair it your self very quickly.
First, you may want to collect your instruments. You will want a wrench, a screwdriver, and a pair of pliers. You may additionally want a brand new washer or O-ring, relying on the reason for the leak. Upon getting your instruments, you are prepared to start out fixing the leak.
Step one is to show off the water provide to the tap. There must be two shut-off valves underneath the sink. As soon as the water is turned off, you possibly can take away the handles from the tap. To do that, merely unscrew the screws which can be holding them in place. As soon as the handles are eliminated, you’ll see the cartridge or stem that controls the stream of water. If the washer or O-ring on the cartridge or stem is worn or broken, it is going to have to be changed. To do that, merely take away the previous washer or O-ring and change it with a brand new one.
Establish the Leak Supply
Figuring out the origin of a leaky bathtub faucet is essential for devising an efficient restore technique. Here is an in depth exploration of widespread leak sources:
1. Deal with Washer:
A worn or deteriorated deal with washer is a frequent offender for leaks. Examine the washers beneath the tap handles. If they seem cracked, pitted, or laborious, they want substitute. Tightening the deal with screws might also resolve a unfastened washer.
2. O-Rings and Gaskets:
O-rings and gaskets create seals to stop leaks at numerous joints inside the faucet. Over time, these seals can put on out, inflicting drips. Verify for any seen injury or hardening of the seals, and change them if essential.
3. Cartridge:
In single-handle taps, a cartridge controls water stream. A defective or broken cartridge can result in leaks. Examine the cartridge by eradicating the deal with and inspecting its situation. If it is worn or broken, substitute is really helpful.
| Frequent Leak Sources | Indicators to Look For |
| — | — |
| Deal with Washer | Cracked, pitted, or laborious washers beneath the handles |
| O-Rings and Gaskets | Worn or hardened seals at joints inside the faucet |
| Cartridge (Single-Deal with Taps) | Worn or broken cartridge underneath the deal with |
Collect the Essential Instruments
To repair a leaky bathtub faucet with two handles, you may want the next instruments:
- Adjustable wrench
- Allen wrench (hex key)
- Phillips head screwdriver
- Flathead screwdriver
- Alternative faucet handles (if essential)
In case you’re undecided what measurement of Allen wrench or Phillips head screwdriver you want, you possibly can often discover the proper measurement listed on the tap’s packaging or within the producer’s directions.
Alternative Faucet Handles
Alternative handles are available in a wide range of types to match your toilet decor. In case you’re undecided what model you need, you possibly can deliver an image of your toilet to the ironmongery store and ask for assist selecting a brand new deal with.
| Deal with Type | Description |
|---|---|
| Lever | A single lever that controls each the water temperature and stream fee. |
| Cross | Two handles which can be perpendicular to one another, one for decent water and one for chilly water. |
| Knob | Two knobs which can be turned to regulate the water temperature and stream fee. |
Flip Off the Water Provide
Earlier than trying any repairs in your leaky bathtub faucet, it is essential to chop off the water provide to the tap to make sure your security and stop water injury. Comply with these steps:
Find the Shut-Off Valves:
Establish the cold and warm water shut-off valves positioned beneath the sink or behind the entry panel within the wall.
Establish the Right Valves:
Activate the tap and observe which shut-off valve stops the stream of water. The valve controlling the chilly water provide usually has a blue deal with or marking, whereas the new water shut-off valve has a purple deal with or marking.
Flip Off the Valves:
Utilizing a wrench or pliers, gently flip the shut-off valves clockwise till they’re utterly closed. Guarantee each the cold and warm water provides are turned off.
Verify for Leaks:
After turning off the valves, activate the tap once more to launch any remaining water strain. If there are not any leaks, you’ve got efficiently turned off the water provide to the tap.
| Valve Kind | Figuring out Function |
|---|---|
| Chilly Water | Blue deal with or marking |
| Sizzling Water | Purple deal with or marking |
Take away the Deal with Caps
Earlier than you possibly can entry the interior parts of the tap, it’s essential take away the deal with caps. These caps often have small screws that maintain them in place. Use a screwdriver to rigorously take away the screws. As soon as the screws are eliminated, you possibly can gently pry off the deal with caps.
Warning:
Watch out to not injury the deal with caps or the tap when eradicating them.
Frequent Sorts of Deal with Cap Screws
| Screw Kind | Description |
|---|---|
| Phillips | Cross-shaped head |
| Hex | Six-sided head |
| Slotted | Straight, flat head |
Ideas for Eradicating Deal with Caps:
- If the screws are rusted or caught, apply penetrating oil and let it sit for a couple of minutes earlier than trying to take away them.
- Use a screwdriver that matches snugly into the screw head to keep away from stripping it.
- Apply light strain when prying off the deal with caps to stop damaging them or breaking the tap.
Take away the Deal with Screws
To take away the deal with screws, you will have a Phillips head screwdriver. Find the screws on the highest or aspect of the deal with. Fastidiously take away the screws and set them apart in a protected place.
If the screws are corroded or tough to take away, you possibly can attempt utilizing a penetrating oil lubricant. Apply a couple of drops of the lubricant to the screws and let it sit for a couple of minutes earlier than trying to take away them. Watch out to not use extreme power when eradicating the screws, as it’s possible you’ll injury the deal with or the tap.
As soon as the screws have been eliminated, the deal with ought to be capable to be pulled off the tap. If the deal with is caught, it’s possible you’ll want to softly wiggle it backwards and forwards till it comes unfastened.
Security Precautions
When engaged on plumbing fixtures, it is very important take the next security precautions:
| Security Precaution |
|---|
| Flip off the water provide to the tap earlier than starting work. |
| Put on security glasses to guard your eyes from particles. |
| Use warning when dealing with sharp objects, corresponding to screwdrivers and pliers. |
Substitute the Worn-out Washer
The washer is a small rubber or plastic disc that sits between the stem and the seat of the tap. Over time, the washer can change into worn or broken, inflicting the tap to leak. Changing the washer is a comparatively easy restore that may be completed in a couple of minutes.
To switch the washer, you will have the next instruments:
- Screwdriver
- Wrench
- Alternative washer
Upon getting gathered your instruments, observe these steps to exchange the washer:
1. Flip off the water provide to the tap.
Find the water provide valves beneath the sink and switch them off. This can stop water from spraying out of the tap if you take away the deal with.
2. Take away the deal with.
Utilizing a screwdriver, take away the screws holding the deal with in place. If the screws are corroded, it’s possible you’ll want to make use of a penetrating lubricant to loosen them. As soon as the screws are eliminated, pull the deal with straight as much as take away it.
3. Take away the packing nut.
Beneath the deal with, you will notice a packing nut. Take away the packing nut utilizing a wrench. Watch out to not overtighten the wrench, as this could injury the packing nut.
4. Take away the stem.
As soon as the packing nut is eliminated, you possibly can take away the stem. Grip the stem with a wrench and switch it counterclockwise to take away it.
5. Examine the washer.
Examine the washer for any indicators of wear and tear or injury. If the washer is broken, it is going to have to be changed.
6. Set up the brand new washer.
Place the brand new washer on the stem. Be sure the washer is seated correctly towards the seat of the tap. Then, change the stem, packing nut, and deal with in reverse order.
7. Activate the water provide and verify for leaks.
Activate the water provide and verify for any leaks. If there are not any leaks, the restore is full.
Substitute the O-Ring if Essential
The O-ring is a small, rubber washer that sits between the deal with and the tap physique. Over time, the O-ring can change into worn or broken, inflicting the tap to leak. Changing the O-ring is a comparatively easy job that may be accomplished in a couple of minutes.
To switch the O-ring, you will have a brand new O-ring that’s the identical measurement because the previous one. You could find new O-rings at most {hardware} shops or residence enchancment facilities.
Upon getting the brand new O-ring, observe these steps to exchange it:
1. Flip off the water provide to the tap.
2. Take away the deal with from the tap.
3. Find the O-ring on the deal with or the tap physique.
4. Use a small screwdriver or your fingernail to take away the previous O-ring.
5. Apply a small quantity of plumber’s grease to the brand new O-ring.
6. Set up the brand new O-ring on the deal with or faucet physique.
7. Reinstall the deal with on the tap.
8. Activate the water provide and verify for leaks.
Listed here are some extra ideas for changing the O-ring:
| Tip | Description |
|---|---|
| Be sure that the brand new O-ring is identical measurement because the previous one. | If the brand new O-ring is simply too massive, it is not going to match correctly and the tap will nonetheless leak. |
| Apply a small quantity of plumber’s grease to the brand new O-ring earlier than putting in it. | This can assist to create a watertight seal and stop the O-ring from leaking. |
| Take a look at the tap for leaks after changing the O-ring. | Activate the water provide and verify for any leaks across the deal with or faucet physique. If there are any leaks, tighten the deal with or change the O-ring. |
Reinstall the Deal with
As soon as the brand new cartridge is in place, you possibly can reinstall the deal with. First, insert the deal with’s stem into the opening on the entrance of the tap. Then, use a screwdriver to tighten the deal with’s screw. Make sure to tighten the screw till the deal with is cosy, however don’t overtighten it. As soon as the deal with is in place, you possibly can activate the water and verify for leaks.
In case you proceed to expertise leaks, it’s possible you’ll want to exchange the O-rings within the deal with. O-rings are small, rubber washers that create a seal between the deal with and the tap physique. Over time, O-rings can change into worn or broken, which might result in leaks. To switch the O-rings, you will have to take away the deal with from the tap. As soon as the deal with is eliminated, you need to use a decide or a small screwdriver to take away the previous O-rings. Then, apply a small quantity of silicone grease to the brand new O-rings and set up them within the deal with.
As soon as the brand new O-rings are in place, you possibly can reinstall the deal with on the tap. Make sure to tighten the deal with’s screw till it’s cosy, however don’t overtighten it. As soon as the deal with is in place, you possibly can activate the water and verify for leaks.
Activate the Water Provide Slowly
Upon getting changed the washer, activate the water provide slowly. Open the new water deal with first, after which the chilly water deal with. This can assist to stop any sudden bursts of water from damaging the brand new washer.
Verify for Leaks
As soon as the water is turned on, verify for any leaks across the faucet. If there are any leaks, tighten the packing nut with a wrench till the leak stops. Watch out to not overtighten the packing nut, as this could injury the tap.
Alter the Handles
If the handles are unfastened, tighten them with a screwdriver. If the handles are too tight, loosen them with a screwdriver. The handles must be cosy sufficient to remain in place, however not so tight that they’re tough to show.
Lubricate the Handles
If the handles are squeaky or tough to show, lubricate them with a silicone-based lubricant. Apply the lubricant to the bottom of the handles, the place they meet the tap physique. This can assist to cut back friction and make the handles simpler to show.
Reset the Cartridge
If the tap remains to be leaking after you’ve got changed the washer and tightened the packing nut, the cartridge could have to be reset. To reset the cartridge, flip off the water provide to the tap and take away the deal with. Then, use a wrench to loosen the cartridge nut and take away the cartridge. Clear the cartridge and the within of the tap physique with a material. Apply a silicone-based lubricant to the cartridge and reinstall it. Lastly, tighten the cartridge nut and reinstall the deal with.
| Instruments You will Want: | Supplies You will Want: |
|---|---|
| Wrench | Faucet washer |
| Screwdriver | |
| Silicone-based lubricant |
Take a look at the Faucet for Leaks
Find the 2 handles in your bathtub faucet and switch them absolutely counterclockwise to show off the water provide.
Open the tap handles all the best way to permit any remaining water to empty out.
Put a small bucket or bowl beneath the tap to catch any dripping water.
Flip each handles again on absolutely to permit water to stream by means of the tap.
Observe the tap for any leaks. In case you discover water dripping from the handles, the bottom of the tap, or the spout, proceed to the following steps.
Establish the Kind of Leak:
| Kind of Leak | Trigger |
|---|---|
| Deal with Leak | Worn or broken O-rings or washers |
| Base Leak | Unfastened or damaged gasket |
| Spout Leak | Deteriorated O-rings or seals inside the spout |
Upon getting recognized the kind of leak, you possibly can proceed to the suitable restore steps. If you’re uncertain about the reason for the leak, seek the advice of knowledgeable plumber for help.
How To Repair A Leaky Bathtub Faucet With Two Handles
A leaky bathtub faucet is usually a main annoyance, however it’s additionally a comparatively simple drawback to repair. With a couple of easy instruments and a little bit little bit of time, you possibly can shortly get your faucet again in working order.
Here is what you may want:
* Adjustable wrench
* Phillips head screwdriver
* Flathead screwdriver
* O-rings (if essential)
Upon getting your instruments and supplies, observe these steps:
1. Flip off the water provide to the tap. You will discover the shutoff valves underneath the sink.
2. Take away the aerator from the tap spout. That is often completed by unscrewing it by hand.
3. Take away the deal with(s). That is often completed by eradicating the screws that maintain them in place.
4. Take away the cartridge(s). That is completed by unscrewing the retaining nut(s).
5. Examine the O-rings on the cartridge(s) for put on or injury. If the O-rings are worn or broken, they are going to have to be changed.
6. Apply a skinny layer of silicone grease to the brand new O-rings.
7. Reinstall the cartridge(s) and tighten the retaining nut(s).
8. Reinstall the deal with(s) and tighten the screws.
9. Reinstall the aerator.
10. Activate the water provide and verify for leaks.
Folks Additionally Ask About How To Repair A Leaky Bathtub Faucet With Two Handles
How do I do know if my bathtub faucet is leaking from the deal with or the spout?
If the water is leaking from the bottom of the deal with, it’s seemingly coming from the cartridge. If the water is leaking from the spout, it’s seemingly coming from the O-rings on the cartridge.
How usually ought to I change the O-rings on my bathtub faucet?
The O-rings in your bathtub faucet must be changed each few years, or extra usually should you discover any leaks.
Can I repair a leaky bathtub faucet myself?
Sure, fixing a leaky bathtub faucet is a comparatively simple restore that may be completed with a couple of easy instruments.
