Mounting your Samsung monitor to its stand is a fast and straightforward course of that may be accomplished in only a few minutes. By following these easy directions, you may make sure that your monitor is securely connected and positioned at an optimum viewing angle.
Step one is to establish the kind of mount that your monitor has. Samsung displays sometimes include both a spherical or sq. mount. Upon getting recognized the kind of mount, find the corresponding mounting bracket on the again of the monitor. The mounting bracket can have a number of holes that line up with the holes on the stand.
Subsequent, align the mounting bracket with the stand and insert the screws into the holes. Tighten the screws till the monitor is securely connected to the stand. As soon as the monitor is connected, you may modify the peak and tilt of the monitor to realize essentially the most snug viewing place. The stand’s built-in swivel lets you rotate the monitor from panorama to portrait orientation, offering most flexibility to your workspace.
Assembling the Stand’s Base
Step one in establishing your Samsung monitor is assembling the stand’s base. It is a simple course of that may be accomplished in a couple of minutes.
To start, lay the stand flat on a steady floor. Then, find the 2 screws which might be connected to the underside of the bottom.
| Step | Description |
|---|---|
| 1 | Take the bottom of the stand and take away the 2 screws from the underside |
| 2 | Insert the stand’s mounting arm into the bottom from the center again. |
| 3 | Safe the mounting arm to the bottom utilizing the 2 screws that have been eliminated earlier. |
| 4 | Flip the bottom over in order that it’s going through upwards. |
| 5 | Connect the monitor to the mounting arm by sliding it down from the highest. |
| 6 | Safe the monitor to the mounting arm utilizing the screws supplied. |
Inserting the Vertical Arm into the Base
To insert the vertical arm into the bottom, comply with these steps:
1. Take away the protecting cowl from the bottom.
Find the protecting cowl on the bottom and take away it. The quilt is normally held in place by screws or clips.
2. Orient the vertical arm and insert it into the bottom.
Orient the vertical arm in order that the cable port is going through down. Align the vertical arm with the opening within the base and insert it.
To insert the vertical arm into the bottom:
- Maintain the vertical arm with one hand and the bottom with the opposite hand.
- Align the grooves on the vertical arm with the rails inside the bottom.
- Slide the vertical arm into the bottom till it snaps into place.
- Tighten the screws or clips that safe the vertical arm to the bottom.
3. Reattach the protecting cowl.
Reattach the protecting cowl to the bottom. This may assist to guard the vertical arm and the bottom from mud and harm.
| Step | Motion |
|---|---|
| 1 | Take away the protecting cowl from the bottom. |
| 2 | Orient the vertical arm and insert it into the bottom. |
| 3 | Reattach the protecting cowl. |
Tightening the Screws to Safe the Stand
As soon as the stand is in place, it is time to tighten the screws to safe it. Don’t overtighten the screws, as this may harm the stand or the monitor. You must tighten the screws till they’re simply comfortable, then cease.
To tighten the screws, you have to the included wrench or a Phillips head screwdriver. Insert the wrench or screwdriver into the pinnacle of the screw and switch it clockwise to tighten. Be sure you tighten all 4 screws evenly. The tightening torque of the screws is 2.5-3.0 kgf.cm (24.5-29.4 in-lb).
If you’re utilizing a Phillips head screwdriver, make sure to use a screwdriver that’s the right measurement. Utilizing a screwdriver that’s too small can strip the screw head, making it troublesome to take away the screw. If you’re utilizing a wrench, make sure to use a wrench that’s the right measurement. Utilizing a wrench that’s too massive can harm the screw or the stand.
| Step | Description |
|---|---|
| 1 | Insert the wrench or screwdriver into the pinnacle of the screw. |
| 2 | Flip the wrench or screwdriver clockwise to tighten the screw. |
| 3 | Repeat steps 1 and a couple of for the opposite three screws. |
Finishing the Monitor Stand Meeting
Putting in the Stand Base and Column
1. Align the bottom’s mounting groove with the column’s attachment level.
2. Slide the column into the bottom till it clicks into place.
Attaching the Head to the Column
3. Find the screw gap on the again of the monitor head.
4. Screw the supplied bolt into the outlet.
5. Align the bolt with the outlet on the highest of the column.
6. Slide the pinnacle onto the column and tighten the screw.
Mounting the Monitor on the Stand
7. Mount the monitor onto the stand by aligning the mounting grooves on each side.
8. Slide the monitor down till it clicks into place.
Adjusting the Monitor
9. Regulate the peak, tilt, and swivel of the monitor as desired.
Utilizing the Spherical Mount Adapter
10. If crucial, use the supplied spherical mount adapter to connect the monitor to an current stand or mounting arm.
10.1. For VESA-compatible stands, comply with these steps:
10.2. For non-VESA-compatible stands, seek the advice of the producer’s directions.
| VESA-Appropriate Stands | Non-VESA-Appropriate Stands |
|—|—|
| – Connect the spherical mount adapter to the again of the monitor. | – Seek the advice of the producer’s directions. |
| – Tighten the screws to safe the adapter. | – Comply with the precise mounting process supplied. |
How To Connect Samsung Stand To The Monitor Spherical Mount
To connect the Samsung stand to the monitor’s spherical mount, you have to the next instruments and supplies:
– Samsung monitor with spherical mount
– Samsung stand
– Phillips head screwdriver
Comply with these steps to connect the stand to the monitor:
1. Place the monitor face down on a mushy floor, akin to a towel or blanket.
2. Find the 4 screws on the again of the monitor that safe the spherical mount.
3. Take away the screws utilizing the Phillips head screwdriver.
4. Align the stand with the spherical mount on the again of the monitor.
5. Insert the screws into the holes on the stand and tighten them utilizing the Phillips head screwdriver.
6. Flip the monitor over and place it on a flat floor.
7. Your Samsung stand is now connected to the monitor.
Individuals Additionally Ask
How do I connect my Samsung monitor to the stand?
To connect your Samsung monitor to the stand, you have to to align the stand with the spherical mount on the again of the monitor and insert the screws into the holes on the stand and tighten them utilizing the Phillips head screwdriver.
What kind of screwdriver do I would like to connect the Samsung stand to the monitor?
You have to a Phillips head screwdriver to connect the Samsung stand to the monitor.
The place can I discover the screws to connect the Samsung stand to the monitor?
The screws to connect the Samsung stand to the monitor are situated on the again of the monitor, securing the spherical mount.
