Within the coronary heart of your Maytag washer, the agitator stands because the tireless workhorse liable for scrubbing away grime and dirt out of your garments. Nonetheless, when upkeep beckons or upgrades name, eradicating the agitator turns into a needed job. Whether or not you are tackling a DIY restore or just searching for a deeper clear, understanding learn how to take away an agitator from a Maytag washer is essential. This complete information will stroll you thru the method, empowering you to revive your washer’s effectivity and hold your laundry glowing.
Earlier than embarking on the removing course of, it is important to collect the required instruments. A sturdy screwdriver, a pair of adjustable pliers, and a cap wrench ought to suffice for many Maytag washer fashions. Make sure that the washer is disconnected from the ability supply and the water provide to make sure your security. With these preparations in place, you’ll be able to proceed to the following step, which entails eradicating the agitator cap.
Find the agitator cap on the prime of the agitator and use the screwdriver to rigorously pry it unfastened. As soon as the cap is eliminated, you can entry the bolt securing the agitator to the transmission shaft. Make use of the adjustable pliers to loosen the bolt by turning it counterclockwise. As soon as the bolt is loosened, you’ll be able to carry the agitator straight up and out of the washer. Deal with the agitator with care throughout removing to stop injury to your self or the equipment.
Figuring out the Washer Mannequin
To start the method of eradicating the agitator out of your Maytag washer, it’s essential to precisely establish the mannequin of your washer. This step is important as totally different Maytag washer fashions have various designs and disassembly procedures for the agitator. To find out the mannequin variety of your washer, observe these detailed steps:
Finding the Mannequin Quantity Tag
Find the mannequin quantity tag on the washer. This tag is often a silver or white label hooked up to the again or facet of the washer. The tag comprises the mannequin quantity, serial quantity, and different related details about your washer.
Studying the Mannequin Quantity
Learn the mannequin quantity on the tag. The mannequin quantity is often a mix of letters and numbers, similar to “MVWB855DW0.” The primary two letters of the mannequin quantity point out the model of the washer, on this case, “MV” stands for “Maytag.” The next characters signify the particular mannequin and its options.
Utilizing the Mannequin Quantity to Discover Disassembly Directions
After you have the mannequin quantity, you should use it to seek out particular disassembly directions on your Maytag washer. You’ll be able to confer with the person handbook that got here together with your washer or seek for on-line sources that present step-by-step directions primarily based on the mannequin quantity.
Disconnecting Energy and Water
Turning Off the Energy
Earlier than touching any electrical parts, it’s vital to make sure security by disconnecting the washer from its energy supply. Find the circuit breaker or fuse field that controls the washer’s electrical energy and change it off. Moreover, unplug the washer from {the electrical} outlet to remove any lingering energy potential.
Shutting Off the Water Provide
Figuring out the Water Shut-Off Valves
Find the water shut-off valves for each the cold and hot water strains operating to the washer. These valves are normally discovered close to the bottom of the washer, behind or under the equipment. They might be labeled as “scorching” and “chilly” or have coloured handles (crimson for warm, blue for chilly).
Turning Off the Valves
Slowly flip the water shut-off valves clockwise till they’re totally closed. You need to really feel resistance as you flip the valves. As soon as closed, the water provide to the washer shall be utterly shut off.
| Valve Coloration | Water Sort |
|---|---|
|
Crimson |
Scorching |
|
Blue |
Chilly |
Eradicating the Console
After disconnecting the washer, eradicating the highest panel, and finding the agitator, it’s essential to detach the console panel. This course of entails a number of steps:
1. Disconnect the Wires
Find the wiring harness linked to the console. Gently disconnect every wire by urgent the discharge tab or squeezing the connector. Hold observe of which wire goes the place for straightforward reassembly.
2. Take away the Screws
Utilizing a Phillips head screwdriver, take away the screws that safe the console to the washer body. Sometimes, there are two screws on the prime and two on the backside of the console.
3. Detach the Console
As soon as the wires are disconnected and the screws are eliminated, you’ll be able to rigorously detach the console from the washer physique. Seize the console by each side and pull it straight up and away from the body. Keep away from prying or twisting, as it could injury the console or its parts.
| Instruments Required | Steps |
|---|---|
| Phillips head screwdriver | Take away the screws securing the console to the washer body. |
| Palms | Rigorously detach the console from the washer physique by pulling it straight up and away from the body. |
Eradicating the Prime Panel
1. Unplug the washer and switch off the water provide.
2. Find the 2 screws on the again of the washer that maintain the highest panel in place. Use a screwdriver to take away the screws.
3. Elevate the highest panel up and off the washer. Watch out to not injury the wires or hoses which are hooked up to the panel.
4. Find the agitator cap on the middle of the agitator. Use a screwdriver to take away the cap.
5. Grasp the agitator and pull it straight up and out of the washer. Watch out to not injury the agitator or the washer.
Extra Notes for Eradicating the Agitator:
- If the agitator is caught, you’ll be able to strive utilizing a pair of pliers to softly pry it unfastened.
- If the agitator remains to be caught, you might have to take away the agitator shaft from the underside of the washer. To do that, find the bolt that holds the agitator shaft in place and take away it utilizing a wrench.
- As soon as the agitator shaft is eliminated, it is possible for you to to drag the agitator up and out of the washer.
Finding the Agitator Bolt
Find the bolt holding the agitator in place. The bolt is often discovered within the heart of the agitator cap. It might be lined by a plastic cap or a steel cowl. If there’s a plastic cap, pry it off with a screwdriver. If there’s a steel cowl, take away it with a wrench.
Figuring out Bolt Look
The agitator bolt is often a big, hexagonal bolt. It might be manufactured from steel or plastic. The bolt head could have a slot for a screwdriver or a gap for a wrench.
Trying to find Bolt Inside Deep Agitator
If the agitator is deep, you might want to make use of a flashlight to find the bolt. Shine the flashlight into the middle of the agitator and search for the bolt head.
Finding Bolt Beneath Agitator
On some Maytag washers, the agitator bolt is situated beneath the agitator. To entry the bolt, you will want to take away the agitator. Discuss with the part under on “Eradicating the Agitator” for directions.
Bolt Not Seen
Should you can not discover the agitator bolt, seek the advice of the Maytag washer handbook or contact Maytag customer support for help.
| Bolt Look | Bolt Location |
|---|---|
| Hexagonal bolt | Heart of agitator cap |
| Steel or plastic | Inside deep agitator (could require flashlight to find) |
| Slot for screwdriver or gap for wrench | Beneath agitator (some Maytag fashions) |
Unscrewing the Agitator Bolt
The agitator bolt is normally situated within the heart of the agitator. It might be hidden beneath a cap or cowl. In that case, use a screwdriver to take away the cap or cowl.
As soon as the bolt is uncovered, use a socket wrench or adjustable wrench to loosen it. Watch out to not overtighten the bolt, as this might injury the washer.
If the bolt is rusted or seized, you might want to make use of a penetrating oil to loosen it. Apply the oil to the bolt and let it sit for a couple of minutes earlier than attempting to loosen it once more.
As soon as the bolt is unfastened, take away it by hand.
Ideas for Eradicating a Rusted or Seized Agitator Bolt
| Tip | Description |
|---|---|
| Use a penetrating oil | Apply penetrating oil to the bolt and let it sit for a couple of minutes earlier than attempting to loosen it. |
| Use a warmth gun | Warmth the bolt with a warmth gun to loosen the rust and make it simpler to take away. |
| Use a chisel | Use a chisel to interrupt the rust bond between the bolt and the agitator. |
| Use a hammer | Faucet the bolt with a hammer to loosen the rust and make it simpler to take away. |
Lifting and Eradicating the Agitator
1. Unplug the washer
Earlier than you begin engaged on the washer, all the time unplug it from the ability outlet. This may assist forestall any electrical shock or damage.
2. Take away the highest cowl
The highest cowl of the washer is normally held in place by just a few screws. Take away these screws and carry the highest cowl off the washer.
3. Find the agitator
The agitator is the big, plastic piece within the heart of the washer tub. It’s used to agitate the garments throughout the wash cycle.
4. Take away the agitator cap
The agitator cap is the small, plastic piece that covers the highest of the agitator. It’s normally held in place by just a few screws. Take away these screws and carry the agitator cap off the agitator.
5. Take away the agitator bolt
The agitator bolt is the big bolt that holds the agitator in place. It’s situated within the heart of the agitator. Use a wrench to take away the agitator bolt.
6. Elevate the agitator
As soon as the agitator bolt is eliminated, you’ll be able to carry the agitator out of the washer tub. Watch out to not drop the agitator, as it’s heavy.
7. Take away the agitator canine
The agitator canine are the small, plastic items that connect the agitator to the transmission. Use a screwdriver to take away the agitator canine from the agitator.
| Instruments wanted | Supplies wanted |
|---|---|
| Wrench | None |
| Screwdriver | None |
1. Unplug the Washer and Flip Off the Water Provide
Earlier than you start, make sure the washer is disconnected from the ability supply and the water provide is turned off. Find the water provide valves behind the washer and switch them clockwise to shut them.
2. Take away the Cloth Softener Dispenser
Find the material softener dispenser on the prime of the agitator. Gently pull it straight as much as take away it.
3. Take away the Agitator Cap
There ought to be a plastic cap on prime of the agitator. Take away it by gently pulling it straight up.
4. Take away the Bolt
Beneath the cap, you will see that a bolt that secures the agitator. Use a socket wrench or adjustable wrench to loosen and take away the bolt.
5. Pull Out the Agitator
As soon as the bolt is eliminated, grasp the agitator firmly and pull it straight as much as take away it from the washer.
6. Cleansing the Agitator
Use a mix of heat water and dish cleaning soap to wash the agitator. Scrub it with a mushy material or sponge to take away any grime or residue. Rinse completely with clear water and let it air dry.
7. Cleansing the Washer
Take away any remaining cloth softener or bleach residue from the washer tub utilizing a material or sponge. Run a scorching water cycle with a cup of white vinegar to sanitize the washer.
8. Reinstalling the Agitator
Place the agitator again into the washer and safe it with the bolt. Tighten the bolt securely utilizing the wrench.
| Exchange the agitator cap. | Exchange the material softener dispenser. |
| Plug within the washer. | Activate the water provide. |
Eradicating the Agitator
1. Shut off the washer and unplug it from the ability outlet.
2. Take away the agitator cap by gently prying it off with a flat-head screwdriver.
3. Use a wrench to loosen the agitator bolt, situated on the backside of the agitator.
4. Rigorously carry the agitator straight up and out of the washer.
Changing the Eliminated Components
5. To exchange the agitator, merely reverse the steps above. Ensure that to tighten the agitator bolt securely.
6. Exchange the agitator cap by snapping it again into place.
7. Plug the washer again into the ability outlet and switch it on to check the agitator.
Troubleshooting
8. If the agitator remains to be not working, there could also be an issue with the agitator motor or the transmission. You have to to contact a professional equipment restore technician to diagnose and restore the difficulty.
Stopping Future Issues
9. To stop future issues together with your Maytag washer agitator, it is very important:
| Keep away from overloading the washer. | Use the right amount of detergent. | Clear the washer repeatedly. | Name a professional equipment restore technician for any service or repairs. |
|---|
Security Precautions
Earlier than beginning any work in your washer, it is very important take some security precautions to keep away from damage or injury to the equipment. First, unplug the washer from {the electrical} outlet. Then, flip off the water provide to the machine. Lastly, placed on a pair of rubber gloves to guard your palms from sharp edges and chemical substances.
Troubleshooting
If you’re having hassle eradicating the agitator out of your Maytag washer, there are some things you’ll be able to strive. First, test to be sure that the wash cycle is full. The agitator is not going to unlock if the cycle remains to be operating. Second, strive turning the agitator forwards and backwards. This will assist to loosen it up and make it simpler to take away. Lastly, if you’re nonetheless unable to take away the agitator, you might have to name a professional equipment restore technician.
10. The right way to Clear the Agitator
After you have eliminated the agitator, it is very important clear it completely earlier than reinstalling it. To wash the agitator, use a light detergent and a mushy material. Remember to rinse the agitator effectively with clear water and dry it utterly earlier than reinstalling it. If the agitator could be very soiled, you might have to soak it in an answer of water and vinegar for a number of hours to take away all the grime and dirt.
By following these steps, you’ll be able to safely take away the agitator out of your Maytag washer and clear it completely. If you’re having any hassle eradicating the agitator, be sure you name a professional equipment restore technician for help.
How To Take away Agitator From Maytag Washer
To take away the agitator from a Maytag washer, you will want a 5/16-inch socket wrench and a flat-head screwdriver.
Comply with the steps under to securely take away the agitator:
- Unplug the washer from {the electrical} outlet.
- Flip off the water provide to the washer.
- Take away the 2 5/16-inch bolts that safe the agitator to the transmission.
- Use a flat-head screwdriver to pry the agitator unfastened from the transmission.
- As soon as the agitator is unfastened, carry it straight up and out of the washer.
If you’re having problem eradicating the agitator, there could also be a small plastic clip that’s holding it in place. Use a flat-head screwdriver to launch the clip after which carry the agitator out.
Folks additionally ask about How To Take away Agitator From Maytag Washer
How do I take away the middle agitator from a Maytag washer?
To take away the middle agitator from a Maytag washer, you will want a 5/16-inch socket wrench and a flat-head screwdriver. Comply with the steps under :
- Unplug the washer from {the electrical} outlet.
- Flip off the water provide to the washer.
- Take away the 2 5/16-inch bolts that safe the agitator to the transmission.
- Use a flat-head screwdriver to pry the agitator unfastened from the transmission.
- As soon as the agitator is unfastened, carry it straight up and out of the washer.
How do I take the agitator out of a Maytag Centennial washer?
To take away the agitator from a Maytag Centennial washer, you will want a 7/16-inch socket wrench and a flat-head screwdriver. Comply with the steps under :
- Unplug the washer from {the electrical} outlet.
- Flip off the water provide to the washer.
- Take away the 2 7/16-inch bolts that safe the agitator to the transmission.
- Use a flat-head screwdriver to pry the agitator unfastened from the transmission.
- As soon as the agitator is unfastened, carry it straight up and out of the washer.
Is it troublesome to take away a Maytag washer agitator?
Eradicating a Maytag washer agitator isn’t a troublesome job. It may be executed in about quarter-hour with the appropriate instruments.
