The Toyota Prius, identified for its gasoline effectivity and eco-friendly repute, is a well-liked alternative amongst drivers looking for a dependable and environmentally aware automobile. One widespread upkeep job that Prius house owners might encounter is changing or eradicating the antenna base. Whereas it could seem to be a frightening job, eradicating the Prius antenna base is comparatively easy with the right instruments and some easy steps. Whether or not you are upgrading to a brand new antenna or just have to make repairs, this complete information will offer you detailed directions on easy methods to safely and effectively take away the Prius antenna base out of your 2013 mannequin.
Earlier than embarking on this job, it is important to collect the required instruments and security gear. You will want a Phillips head screwdriver, a flathead screwdriver, a plastic pry device or a spudger, and gloves to guard your fingers. Moreover, make sure you park your Prius in a protected and well-lit space to reduce distractions and enhance visibility. After you have your instruments and security gear prepared, you possibly can proceed with the removing course of by following the step-by-step information outlined beneath.
To start, find the antenna base on the roof of your 2013 Prius. It’s sometimes located close to the middle of the roof and surrounded by a black plastic cowl. Utilizing the flathead screwdriver, gently pry open the plastic cowl by inserting the tip of the screwdriver into the small hole between the quilt and the roof. As soon as the quilt is unfastened, you possibly can take away it fully by hand. Subsequent, use the Phillips head screwdriver to loosen the screws that safe the antenna base to the roof. As soon as the screws are eliminated, you possibly can rigorously pull the antenna base straight up and off the roof. Make sure to deal with the antenna base with care to keep away from damaging it or the encompassing parts.
Find the Antenna Base
The antenna base in your 2013 Prius is positioned on the roof of the automobile, in the direction of the rear. To search out it, observe these steps:
- Stand behind the automobile and search for on the roof.
- Find the black plastic base that’s connected to the roof with a single bolt.
- That is the antenna base.
Here is a extra detailed description of every step:
- Stand behind the automobile and search for on the roof. This provides you with a transparent view of the highest of the automobile.
- Find the black plastic base that’s connected to the roof with a single bolt. The bottom is round and about 2 inches in diameter. It’s positioned in the direction of the rear of the roof, close to the middle.
- That is the antenna base. After you have discovered the bottom, you possibly can proceed to the following step to take away it.
| Step | Description |
|---|---|
| 1 | Stand behind the automobile and search for on the roof. |
| 2 | Find the black plastic base that’s connected to the roof with a single bolt. |
| 3 | That is the antenna base. |
Take away the Inside Trim Panel
To take away the inside trim panel across the base of the antenna, observe these detailed steps:
Step 1: Find the Trim Panel
Establish the trim panel surrounding the antenna base on the headliner. It’s often an oblong or round panel made from plastic or cloth.
Step 2: Detach the Trim Panel
Gently use a pry device or a flat-head screwdriver wrapped in a material to rigorously pry the trim panel unfastened from the headliner. Insert the device into the hole across the fringe of the panel and apply light stress to launch the clips holding it in place. Work across the perimeter of the panel, detaching the clips one after the other.
Step 3: Take away the Trim Panel
As soon as all of the clips are launched, rigorously elevate the trim panel away from the headliner. Disconnect any wiring or cables connected to the panel, akin to these for the antenna or roof gentle (if relevant). Place the trim panel in a protected location to forestall harm.
Detach the Antenna Base
1. Insert a flat-head screwdriver or a trim removing device into the small slot on the base of the antenna. Gently pry the antenna base unfastened from the roof of the automobile.
2. As soon as the antenna base is unfastened, take away it from the automobile and set it apart.
Detach the Antenna Cable
1. Find the antenna cable that’s connected to the bottom of the antenna. The cable will probably be held in place by a small plastic clip or screw.
2. If the cable is held in place by a clip, use a flat-head screwdriver or a trim removing device to pry the clip open and launch the cable.
3. If the cable is held in place by a screw, use a screwdriver to take away the screw and launch the cable.
| Antenna Cable Connector | Removing Methodology |
|---|---|
| Plastic Clip | Pry open the clip with a flat-head screwdriver or a trim removing device. |
| Screw | Take away the screw with a screwdriver. |
4. As soon as the antenna cable is launched, rigorously pull the cable by means of the opening within the roof of the automobile.
5. Disconnect the antenna cable from the antenna base by urgent on the discharge button on the connector and pulling the 2 connectors aside.
Unscrew the Antenna Base Bolts
Now, let’s deal with the true job: eradicating the antenna base. You may want a 10mm socket wrench or a deep socket set for this step.
-
First, find the 4 bolts holding the antenna base to the roof. They need to be organized in a sq. sample.
-
Take your socket wrench and thoroughly insert it into the primary bolt. Flip it counterclockwise to loosen it.
-
Repeat this course of for the remaining three bolts.
-
As soon as all 4 bolts are unfastened, you possibly can take away the antenna base by gently lifting it straight up.
Now that you’ve the antenna base eliminated, you possibly can transfer on to disconnecting the antenna wire. Bear in mind to deal with the antenna with care to keep away from any harm.
Further Suggestions for Unscrewing the Bolts
Listed here are some useful tricks to make unscrewing the bolts simpler and extra environment friendly:
| Tip | Description |
|---|---|
| Use a Deep Socket | A deep socket will present higher entry to the bolts beneath the antenna base. |
| Apply Strain | Apply regular stress to the wrench whereas turning it. Utilizing extreme drive may harm the bolts. |
| Use a Penetrating Oil | If the bolts are rusted or corroded, apply a penetrating oil across the threads to loosen them. |
Take away the Antenna Base
Step 1: Take away the Middle Console
Start by eradicating the middle console by unscrewing the bolts that maintain it in place. As soon as the bolts are eliminated, elevate the console upwards to disconnect it from the automobile’s electrical system.
Step 2: Find the Antenna Connector
Beneath the middle console, you can find the antenna connector. It’s sometimes positioned close to the firewall and linked to a wiring harness.
Step 3: Disconnect the Antenna Wire
Disconnect the antenna wire from the connector by urgent on the discharge button or tab. Observe that the placement and form of the discharge mechanism might differ relying on the particular mannequin 12 months.
Step 4: Unscrew the Antenna Base
Find the antenna base, which is linked to the antenna wire and mounted on the roof of the automobile. Utilizing an acceptable device akin to a wrench or socket, unscrew the antenna base and thoroughly take away it from the roof.
Step 5: Clear and Reinstall the Antenna Base
Earlier than reinstalling the antenna base, it is essential to scrub each the bottom and the mounting floor on the roof. This can guarantee optimum sealing and stop moisture ingress. Apply a skinny layer of sealant or adhesive to the bottom of the antenna earlier than screwing it again into place. Tighten the bolts securely, guaranteeing a cosy and watertight connection.
| Instruments Required | Security Precautions |
|---|---|
| Phillips head screwdriver | Put on gloves to keep away from cuts |
| Wrench or socket | Disconnect the battery earlier than engaged on electrical parts |
| Sealant or adhesive | Park on a steady and stage floor |
Clear the Contact Factors
After eradicating the antenna base, you’ll need to scrub the contact factors the place it connected to the automobile’s roof. Dust and corrosion can construct up over time, inflicting issues with the antenna’s sign reception. To wash the contact factors, use a cotton swab dipped in rubbing alcohol or a specialised contact cleaner. Gently rub the swab over the factors till they’re freed from grime and particles. As soon as the contact factors are clear, enable them to dry fully earlier than reattaching the antenna base.
| Supplies required |
|---|
|
Further suggestions for cleansing the contact factors:
- Watch out to not use an excessive amount of drive when cleansing the contact factors, as this might harm them.
- If the contact factors are closely corroded, chances are you’ll want to make use of a fine-grit sandpaper to take away the corrosion. Make sure to clear the contact factors completely with rubbing alcohol after sanding.
- As soon as the contact factors are clear, apply a small quantity of dielectric grease to them to assist forestall future corrosion.
Reinstall the Antenna Base
As soon as the previous antenna base is eliminated, you possibly can proceed to put in the brand new one. Comply with these steps:
-
Align the brand new antenna base with the mounting holes on the roof.
-
Place the washers onto the bolts.
-
Tighten the bolts utilizing the torque wrench to the required torque setting.
-
Set up the antenna by screwing it onto the antenna base.
-
Join the antenna wire to the antenna base.
-
Safe the antenna wire with the offered zip tie or electrical tape.
-
Check the antenna by turning on the radio and checking for a transparent sign.
| 12 months | Bolt Dimension | Torque (Nm) |
|---|---|---|
| 2013-2018 | M6 | 12-15 |
Safe the Antenna Cable
As soon as the antenna base is eliminated, you will have to safe the antenna cable. Here is easy methods to do it:
Find the Antenna Cable
Establish the antenna cable, which is often a black or grey wire that runs from the antenna base to the again of the automobile.
Disconnect the Antenna Cable
Gently pull the antenna cable straight out of the antenna base. Don’t twist or bend the cable.
Wrap the Antenna Cable
Use electrical tape or a zipper tie to wrap the disconnected antenna cable. This can forestall it from dangling or getting broken.
Route the Antenna Cable
Fastidiously route the wrapped antenna cable alongside the present wiring harness or any designated channels within the automobile’s inside.
Safe the Antenna Cable
Use cable clips or zip ties to safe the antenna cable to the automobile’s body or inside panels. This can maintain it in place and stop it from transferring round.
Reconnect the Antenna Cable
Find the antenna port on the again of the automobile’s radio or audio system. Align the antenna cable with the port and gently push it in till it clicks into place.
Tighten the Antenna Cable
Hand-tighten the antenna cable by turning it clockwise. Don’t overtighten the cable, as this might harm the port or the cable.
Reattach the Inside Trim Panel
9. Reattach the Inside Trim Panel:
| Step | Directions |
|---|---|
| a. | Find the plastic clips across the perimeter of the trim panel. |
| b. | Align the clips with the corresponding slots on the inside panel. |
| c. | Apply stress to the trim panel across the edges to reconnect the clips. |
| d. | Be certain that the trim panel is securely mounted and would not rattle. |
| e. | Tighten the screws within the decrease corners of the trim panel to additional safe it. |
| f. | Fastidiously pull on the trim panel to make sure it’s securely connected. |
| g. | If essential, alter the clips or screws till the trim panel suits snugly. |
| h. | Substitute the A-pillar trim cowl by snapping it again into place. |
| i. | Verify that every one the trim panels, screws, and clips are correctly secured. |
Bear in mind to deal with the trim panels with care to keep away from harm. Should you encounter any difficulties, seek the advice of with a professional mechanic.
Check the Antenna
Earlier than you begin eradicating the antenna base, it is essential to check the antenna to verify it isn’t working correctly. Here is easy methods to do it:
- Flip in your automobile radio.
- Tune to a radio station that you already know has a robust sign.
- Should you hear static or interference, it signifies that your antenna shouldn’t be working correctly.
- Should you do not hear any static or interference, it signifies that your antenna is working correctly and you’ll proceed to eradicating the antenna base.
Listed here are some further suggestions for testing your antenna:
- When you have a multimeter, you should utilize it to check the continuity of the antenna wire.
- It’s also possible to attempt connecting a special antenna to your automobile radio to see if it really works.
- Should you’re nonetheless having hassle, you possibly can take your automobile to a mechanic to have them diagnose the issue.
How To Take away Prius Antenna Base 2013
To take away the Prius antenna base in a 2013 mannequin, observe these steps:
1.
Find the antenna base on the roof of the automobile.
2.
Utilizing a Phillips head screwdriver, take away the 2 screws that safe the antenna base to the roof.
3.
Gently pull up on the antenna base to take away it from the roof.
4.
Disconnect the antenna wire from the antenna base.
5.
Take away the antenna base from the automobile.
Folks Additionally Ask About How To Take away Prius Antenna Base 2013
How do you take away the shark fin antenna on a Prius?
To take away the shark fin antenna on a Prius, observe these steps:
- Find the shark fin antenna on the roof of the automobile.
- Utilizing a Phillips head screwdriver, take away the 2 screws that safe the antenna to the roof.
- Gently pull up on the antenna to take away it from the roof.
- Disconnect the antenna wire from the antenna base.
- Take away the antenna from the automobile.
How do you take away the roof rack on a Prius?
To take away the roof rack on a Prius, observe these steps:
- Find the 4 bolts that safe the roof rack to the roof of the automobile.
- Utilizing a wrench, take away the 4 bolts.
- Gently elevate the roof rack off of the roof of the automobile.
- Take away the roof rack from the automobile.
How do you take away the antenna on a Prius?
To take away the antenna on a Prius, observe these steps:
- Find the antenna on the roof of the automobile.
- Utilizing a Phillips head screwdriver, take away the screw that secures the antenna to the roof.
- Gently pull up on the antenna to take away it from the roof.
- Take away the antenna from the automobile.
